Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Development of a dual‐lamp projector with higher brightness

Stationary projectors mainly used in system applications have recently gained a wider application range, including general presentations in halls and large conference rooms and being used, for example, in digital signage and for monitoring purposes. Consequently, they are required to meet new market demands for durability, reliability, and flexibility in installation in addition to their conventional basic performance such as especially high brightness. To achieve especially high brightness, a new optical system with two lamps is proposed; the profile of the cover glass that prevents the glass from scattering is made aspherical, the profile of the beam‐combining mirror is improved with its position optimized, and the size of the incident plane of the integrator rod is made larger (1.1 times). These measures resulted in an optical system of an even higher efficiency with 7000 lm, which is the highest in its class (according to a June 2010 investigation). Also, the arrangement of two parallel lamps completely eliminated the effect of heat passing from one lamp to the other, which helped secure durability, reliability, and flexibility in installation. Furthermore, the combined use of the unique non‐telecentric optical system, adopted from the conventional single‐lamp model, helps maintain the class‐highest contrast ratio.^1,2     

Application of the solid polymer electrolyte (SPE) method to organic electrochemistry—III. Kolbe type reactions on Pt-SPE

The feasibility of a solid polymer electrolyte (SPE) method for Kolbe type reactions was investigated by using Pt-SPE composed with Nafion 415 and platinum. The Kolbe reaction of acetic acid proceeded effectively on one side and both sides Pt-SPE composites. The lower current efficiency was observed on the latter than on the former. Neat acetic acid could also be electrolysed on both sides SPE though the cell voltage was fairly high.A methanolic solution of monomethyl adipate was electrolysed to give dimethyl sebacate on both sides Pt-SPE according to the Brown-Walker reaction. The current efficiency and the terminal voltage increased with the concentration of monomethyl adipate. Pt-SPE behaved as an active electrode of a high roughness factor, eg about 6, for the Kolbe reaction of acetate.