Sub-50-nm physical gate length CMOS technology and beyond usingsteep halo

Sub-50-nm CMOS devices are investigated using steep halo and shallow source/drain extensions. By using a high-ramp-rate spike annealing (HRR-SA) process and high-dose halo, 45-nm CMOS devices are fabricated with drive currents of 650 and 300 μA/μm for an off current of less than 10 nA/μm at 1.2 V with T_ox^inv =2.5 nm. For an off current less than 300 nA/μm, 33-nm pMOSFETs have a high drive current of 400 uA/μm. Short-channel effect and reverse short-channel effect are suppressed simultaneously by using the HRR-SA process to activate a source/drain extension (SDE) after forming a deep source/drain (S/D). This process sequence is defined as a reverse-order S/D (R-S/D) formation. By using this formation, 24-nm nMOSFETs are achieved with a high drive current of 800 μA/μm for an off current of less than 300 μA/μm at 1.2 V. This high drive current might be a result of a steep halo structure reducing the spreading resistance of source/drain extensions     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Self-healing algorithm for logical mesh connection on ring networks

A self-healing algorithm is proposed for a ring network connected as a logical mesh. It offers good performance in terms of protection line capacity, restoration time, and survivability against multiple failures     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Co-crosslinking blend of incompatible polymers VI: Poly(vinyl chloride) toughened with polyethylene via a co-crosslinking technique

A binary blend which consists of two incompatible polymers such as poly(vinyl chloride) and polyethylene has been performed through a partial co-crosslinking reaction with peroxide to give a co-crosslinked blend with a uniform dispersion of small polyethylene particles and with an improved mechanical property. The results are obtained through the formation of a co-crosslinked product which acts as a potential solid phase dispersant as well as a well-bonded reinforcing interlayer on polyethylene particles uniformly dispersed in poly(vinyl chloride) matrix. The resulting blends (PVC/PE=10/90 wt) give carbon spherules of 0.5 to 1m diameter through pressure-carbonization at 650° C for 1 h.     

New amphoteric surfactants containing a phosphoric acid group: I. syntheses and physicochemical properties of sodium 2-(n-2-hydroxyalkyl-n-methylamino)ethyl hydrogen phosphate

A series of new amphoteric surfactants having a phosphoric acid group, a tertiary amino group and a 2-hydroxyalkyl group, sodium 2-(N-2-hydroxyalkyl-N-methyl-amino)ethyl hydrogen phosphates (alkyl: n-tetradecyl, n-hexadecyl, n-octadecyl), were prepared by an addition reaction of 1,2-epoxyalkanes to N-methylaminoethanol, followed by the introduction of a phosphoric acid group and neutralization with sodium hydroxide. The structures of these compounds were confirmed by spectroscopy and elemental analysis. The solubility in solvents, Krafft point, surface tension, critical micelle concentration (CMC), occupation area of the molecule at the surface of aqueous solutions and foaming power were measured. It was shown that a 2-hydroxyethyl group in a long alkyl chain seemed to behave as a hydrophobic part.     

The degradation of polystyrene during extrusion

An investigation was made of the magnitude and mechanism of shear degradation of a narrow distribution, high molecular weight (M_w = 670,000) polystyrene. An Instron rheometer was used to perform the extrusion at temperatures from 164° to 250°C. The change in molecular weight distribution was studied by gel permeation chromatography. The maximum shear stress employed was 5.83 kg/cm². It was found that degradation could be induced at high stress at temperatures of 50°C lower than degradation of polystyrene would occur exclusively due to thermal forces. An activation energy for the degradation, calculated at constant shear rate, was +20.2 kcal/mole. The direction and magnitude of this value are consistent with degradation induced through a mechanical reduced activation for thermal degradation.     

Effect of Composition and Size of Crystallite on Crystal Phase in Lead Barium Titanate

Lead titanate, barium titanate, and lead barium titanate powders (>99.9% pure), the particle size of which varied from 0.03 to 0.15 μm depending on the calcination temperature and the composition, was prepared from barium lead titanyl oxalate, which was previously prepared by reacting high-purity ammonium titanyl oxalate with barium and lead acetate. The critical crystallite size of BaTiO₃ powder from the cubic to the tetragonal phase is around 1 μm. Pb_0.3Ba_0.7TiO₃ powder with an average size of 0.057 μm showed the tetragonal phase.     

Stabilization of poly(vinyl chloride). I. Change in color of poly(vinyl chloride) compounded with some metal soaps

Poly(vinyl chloride) (PVC) with one or more metal salts added was colored by the action of heat to investigate the stabilization mechanism. The coloration and the color difference of heated PVC compound films varied according to the metal salt added. The decoloration of the colored compound films was advanced markedly in THF, DMF, acetone, and ammonia. On the other hand, the heated achromatic PVC film containing Cd/Ba soaps underwent an opposite change, from colorless to yellow orange, in the above materials. This means that the coloration of heated compound films may result from the formation of some complex (for example, π complex of the polyene with the metal chloride). Furthermore, the colored film with cadmium stearate was decolored by roll mixing with the colored film containing barium stearate. These results indicate that the stabilization with metal soaps may be founded on a physical phenomenon such aa an effect of complementary color.     

A superhydrophilic titanium implant functionalized by ozone gas modulates bone marrow cell and macrophage responses

Bone-forming cells and M? play key roles in bone tissue repair. In this study, we prepared a superhydrophilic titanium implant functionalized by ozone gas to modulate osteoconductivity and inhibit inflammatory response towards titanium implants. After 24 h of ozone gas treatment, the water contact angle of the titanium surface became zero. XPS analysis revealed that hydroxyl groups were greatly increased, but carbon contaminants were largely decreased 24 h after ozone gas functionalization. Also, ozone gas functionalization did not alter titanium surface topography. Superhydrophilic titanium (O₃–Ti) largely increased the aspect ratio, size and perimeter of cells when compared with untreated titanium (unTi). In addition, O₃–Ti facilitated rat bone marrow derived MSCs differentiation and mineralization evidenced by greater ALP activity and bone-like nodule formation. Interestingly, O₃–Ti did not affect RAW264.7 M? proliferation. However, naive RAW264.7 M? cultured on unTi produced a two-fold larger amount of TNFα than that on O₃–Ti. Furthermore, O₃–Ti greatly mitigated proinflammatory cytokine production, including TNFα and IL-6 from LSP-stimulated RAW264.7 M?. These results demonstrated that a superhydrophilic titanium prepared by simple ozone gas functionalization successfully increased MSCs proliferation and differentiation, and mitigated proinflammatory cytokine production from both naive and LPS-stimulated M?. This superhydrophilic surface would be useful as an endosseous implantable biomaterials and as a biomaterial for implantation into other tissues.