Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Density functional theory studies of Cu-zeolite de-NOx catalysts

Summary Recent progress in the modelling of exchanged Cu sites and their interactions with small molecules, based on DFT cluster calculations, is briefly reviewed.     

0.27-dB/km attenuation achieved by MSP preform process [opticalfibers]

Mechanically shaped preforms (MSP) have been demonstrated to combine economic non-CVD (chemical vapor deposition) processing and low loss, with a published value of 0.63 dB/km and a size of 30 fkm/preform. Improved processing is proposed which results in a minimum loss of 0.27 dB/km at 1550 nm. Preforms capable of yielding 150 fkm have been produced. Reboiling during preform stretching and fiber pulling is identified as the last remaining problem of the process     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

Microchemical composition and cell dimensions of mullites from refractory-grade South American bauxites

Two different types of mullite could be determined in differently coloured fragments of South American bauxites: − Mullites, occuring in light bauxite fragments with low impurity contents (Σ wt % (Fe₂O₃ + TiO₂) 2.5), and cell dimensions close to that of 3/2 mullite, the b parameter being slightly shorter. − Mullites, occurring in grey to dark grey, and in brown bauxite fragments, with high impurity contents (Σ wt % (Fe₂O₃ + TiO₂) 4,0) and a and c cell dimensions close to those of 2/1 mullite. The b constant of these mullites is slightly expanded with respect to impurity free mullites. Increasing impurity contents in mullite are linearly correlated with a b expansion. The expansion was structurally explained with a substitution of Al³⁺ by Fe³⁺ and Ti⁴⁺ at octahedral lattice sites, which causes stretching of the AlO₆ octahedra along to the elastic Al₁---D_D bond in mullites which is 30° to either side of b. The substitution-produced expansion is superimposed by an expansion due to the change of the structural state of mullite from the 3/2 to the 2/1 type. The greatest variation in any cell parameter with the change of the structural state is the a constant.     

New aspects of transversal1H-NMR relaxation in natural rubber vulcanizates

Summary Structure and dynamics of unfilled and carbon black filled natural rubber vulcanizates were investigated by means of transversal¹H-NMR-relaxation. A simple theoretical model including different motions in polymer network was extended by the discussion of an anisotropy parameter of segmental motion not only for the intercrosslink chains but also for the dangling ends. It makes characterization of the filling state of the network possible to approximate. The effect of increasing correlation times _f of the fast anisotropic local motion with reduction of the molecular mass of intercrosslink chains which was observed, but not cleared up in previous investigation is evidently smaller by using this modified model in accordance with the expectation of a local motion. The determined values of M_c are in good agreement with the results of fits by using the unmodified relaxation function.¹³C-NMR-spectra and stress-strain-experiments are leading in most cases to similar results, especially for M_c.