Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

Reliability and performance analysis of time – space – time switching networks with multiple separated space switches

Since electronic switching systems usually require very strict reliability requirements as well as good performance objectives, we need to jointly analyse the performance and reliability of switching systems. In this paper, we compare conventional time–space–time switches with single space switches with those with multiple separated space switches, from the viewpoints of reliability and performance. We consider time–space–time switching networks which consist of N incoming time switches, i.e. one NxN space switch, two (N/2)x(N/2) space switches, and four (N/4)x(N/4) space switches. We introduce a Markov reliability model to study the effect of failures and analyse the reliability and performance of three different types of switching networks in terms of average blocking probability and the mean time to unreliable operation, as we vary the offered traffic. As a result, T–S–T switching networks with multiple separated space switches exhibit better performance and reliability than those with single space switches.     

Influence of nitrate, ascorbic acid, and nitrate reductase microorganisms on N-nitrosamine formation during Korean-style soysauce fermentation.

Traditional Korean soysauce samples were collected from households in Chinju, Gyeongnam, Korea and analysed for volatile N-nitrosamines. Five of 24 samples contained NDMA (range = 1.6-10.4 micrograms/l) which was the only volatile N-nitroso compound found. Soysauce made from well water contained NDMA more often (4 of 6 samples) than soysauce made from tap water (1 of 18). This suggests that the water source is a determinate in the NDMA content of soysauce, probably due to a higher nitrate content of well water. The source of salt used did not clearly influence NDMA content. Soysauce was prepared in the laboratory using traditional methods but with 0 to 400 mg/l nitrate and in some cases made 6.5 to 65 mM in ascorbic acid and fermented for 120 days. The NDMA content of the samples was positively correlated with increasing nitrate concentration. Nitrate at 400 mg/l resulted in an NDMA content of 203 micrograms/l. Ascorbic acid substantially inhibited NDMA formation. All samples contained large numbers of nitrate reductase-containing organisms (greater than 1 x 10(7) CFU/ml).     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Porosity distribution in highly compressible cake: Experimental and theoretical verification of the dense skin

The rate of filtration and the water content of cake are influenced by the existence of a dense skin in a highly compressible cake. The phenomenon of the dense skin has been rarely studied, and its existence has not been verified experimentally. In this study, the porosity variation in a very compressible cake is measured by using a new experimental apparatus, and with this the existence of dense skin has been established experimentally. ‘Unified theory on solid-liquid separation’, a recently developed theory, is utilized for calculating the porosity variation in a very compressible cake.     

A linear minimum mean square error multiuser receiver inRayleigh-fading channels

We generalize the multiuser (CDMA spread spectrum) communication systems to the fading environments. We first extend Verdu's (1986) conventional optimum receiver to Rayleigh-fading environments and then evaluate its performance. Having no knowledge of the received power at the receiving end, we therefore need an estimator to efficiently estimate the received signal strength of each user in fading environments. A linear minimum mean square error (LMMSE) unbiased estimator is proposed to attain this goal. By using the minimum mean square error (MMSE) Bayesian estimation, we further propose the LMMSE bit estimator for efficient demodulation. Its performance is close to the optimum multiuser receiver but with a much simpler polynomial complexity. To further reduce the complexity, we extend the LMMSE estimator to the sequential LMMSE estimator. In sequential estimation, we do not need to implement the matched filter banks and to perform the matrix inversion when estimating. In addition, it converges after approximately 2k iterations, where k is the number of users. With this fast convergence property and the simple structure, the sequential LMMSE estimator provides an attractive alternative to the implementation of a multiuser system     

Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

A kinetic model for polystyrene (PS) pyrolysis reaction

A mathematical model for the pyrolysis reaction of polystyrene (PS) in a semi-batch reactor has been presented. The thermal degradation of PS was flexibly modeled by a combination of random and specific chain-end scissions. Numerical simulation was used to investigate the effect of operating conditions on the PS products spectrum, the results of which were validated by the experimental data. It was found that as the reaction temperature increased (decreased), the monomer fraction in the products became lower (higher) while the trimer higher (lower). No significant variation in the product composition was, however, observed while constant temperature was maintained. These results indicate the reaction temperature is an effective manipulated variable for the control of products composition of PS pyrolysis. The calculation of the optimum temperature trajectories through the optimization study can thus be of interest for achieving productivity enhancement in plastics pyrolysis processes. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

Collapse-free thermal bonding technique for large area microchambers in plastic lab-on-a-chip applications

Bonding is an essential step to form microchannels or microchambers in lab-on-a-chip applications. In this paper, we present a novel plastic thermal bonding technique to seal and form large area microchambers (planar characteristic width and length on the order of 1 mm and characteristic thickness on the order of 10–100 μm) without collapse by introducing a holed pressure equalizing plate (HPEP) that includes holes of the same size and shape as the microchambers. To demonstrate the proposed technique, two types of large area microchambers [(1) 20 × 10 mm and 40 μm thick and (2) 12 × 2.5 mm and 120 μm thick] with microchannels were designed and replicated on plastic substrates by means of hot embossing and injection molding processes with prepared two nickel mold inserts. The replicated large area microchambers as well as the microchannels in the plastic lab-on-a-chip were successfully sealed (i.e., no leakage) and formed without any collapse by the proposed thermal bonding technique with the help of the HPEP.