Value analysis of intermittent generation sources from the systemoperations perspective

The objective of this study is to determine the economic and operational impact on energy cost of incorporating large photovoltaic (PV) and wind energy conversion systems (WECS) into the electric utility generation mix. In most cases, PV and WECS power outputs are subtracted from the utility load with the expectation that conventional generation would meet the residual load. This approach is valid for small penetration levels and/or for PV and WECS facilities connected near load centers, However, several constraints such as thermal generation characteristics, fuel supply and delivery, spinning reserve requirements, and hydro availability are not adequately represented in this process. To determine the optimal value of large-scale PV and WECS applications, a new methodology that would take into account the aforementioned constraints as well as a more global penetration is developed. Results indicate that while high hydro availability increases PV penetration levels, high ramping rates can also significantly increase penetration levels     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Simulation and experimental analyses of electromagnetic transients behaviors of lightning surge on vertical conductors

Simulation of very fast surge phenomena in a three-dimensional (3-D) structure requires a method based on Maxwell's equations, such as the finite-difference time-domain (FDTD) method or the method of moments, because circuit-equation-based methods cannot handle the phenomena. This paper uses a method of thin-wire representation of the vertical conductor system for the FDTD method which is suitable for the 3-D surge simulation. The thin-wire representation is indispensable to simulate electromagnetic surges on wires or steel frames in which the radius is smaller than a discretized space step used in the FDTD simulation. In this paper, a general surge analysis program named the virtual surge test lab based on the Maxwell's equations formulated by the FDTD method, is used to simulate the surge phenomena of a vertical conductor, including the effects of horizontal wave incidence and vertical wave incidence. Experimental results on the reduced scale model have been presented in order to compare among the simulation results by the FDTD method and the results using numerical electromagnetic code based on the MoM.     

The functional reanimation of paralyzed limbs.

The functional reanimation of paralyzed limbs has been a longstanding goal of neural prosthetic research, but clinically successful applications have been elusive. Natural voluntary limb movement requires four major elements: actuators (i.e., motor units), sensors (i.e., somatosensory afferents), commands (i.e., cerebral cortical activity), and control (i.e., integration of the previous three elements at various levels of the neuraxis). Prosthetic equivalents of each of these elements are, as yet, primitive and often cumbersome to deploy, but new technologies promise substantial improvements for all. This article focuses on one such technology, bionic neuon (BION) modular microimplants, and its relationship to alternative and complementary technologies. The challenge remains to select and integrate them into systems that can be tailored efficiently to the widely disparate needs of patients with various patterns of weakness and paralysis.     

Purification and renaturation of recombinant human lymphotoxin (tumour necrosis factor beta) expressed in Escherichia coli as inclusion bodies

High level expression of recombinant human tumour necrosis factor β (rh TNF-β) in Escherichia coli results in the formation of two portions of protein, namely soluble active protein and insoluble protein which is inactive and aggregates in the form of inclusion bodies (IBs). In this study, a procedure for purification and renaturation of rh TNF-β from inclusion bodies has been designed and verified experimentally with a product purity of more than 90% and a recovery of about 30%. The procedure includes washing of IBs with specific wash buffer (Triton X-100/EDTA/lysozyme/PMSF), their solubilization with 8 mol dm^?3 alkaline urea, purification with ion-exchange columns, refolding with renaturation buffer and finally concentration and desalination with an ultrafiltration membrane. The characteristics of the renatured protein were identical with those of purified protein from the soluble fraction as demonstrated by (1) SDS-PAGE, (2) cytotoxic activity on mouse L929 cells, (3) N-terminal amino acid sequence, and (4) gel filtration chromatography.     

Modelling and controller design of an isolated diesel enginepermanent magnet synchronous generator

A method to analyze the steady-state performance of a stand-alone permanent magnet synchronous generator driven by a diesel engine is presented. The proposed method is based on equivalent d-q circuits and the phasor diagram of such a generator under steady-state conditions. A fixed capacitor-thyristor controlled reactor scheme is used to regulate the generator terminal voltage by controlling the thyristor ignition angle. Furthermore the overall system dynamics are modelled in terms of state variables and control inputs. Based on a reduced order linearized model, digital optimal state and output feedback controllers are designed by minimising a quadratic performance index using the dynamic programming technique. The objective of the controller is to maintain the load voltage and frequency constant under varying load conditions. The controller's effectiveness is assessed by examining the closed-loop system response to sudden load changes     

High-speed milling of titanium alloys using binderless CBN tools

The performance of conventional tools is poor when used to machine titanium alloys. In this paper, a new tool material, which is binderless cubic boron nitride (BCBN), is used for high-speed milling of a widely used titanium alloy Ti–6Al–4V. The performance and the wear mechanism of the BCBN tool have been investigated when slot milling the titanium alloy in terms of cutting forces, tool life and wear mechanism. This type of tool manifests longer tool life at high cutting speeds. Observations based on the SEM and EDX suggest that adhesion of workpiece and attrition are the main wear mechanisms of the BCBN tool when used in high-speed milling of Ti–6Al–4V.