Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Statistical synchronization among participants in real-time multimedia conferencing

In this paper, an algorithm to determine the set of packets generated continuously and periodically from different participants that are arriving at a node either for mixing at the master of a conference, or for simply playing back at a regular participant of a conference, is proposed. The essence of the algorithm is to estimate the expected packet arrival time (or reference time) for each participant. With the reference time at hand, the maximum jitter and the optimum waiting time for a mixer to wait packets from all participants can be determined. An enhancement to improve synchronization which deals with the estimation of the time offsets between the individual periods of the sources and the period of the receiver is also presented. The error of the proposed algorithm is enumerated by the Chernoff bound and demonstrated by simulation and is shown to be acceptable in practical application. The algorithm can also be employed when traffic sources operate with different periods.     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

Slow eroding biodegradable multiblock poloxamer copolymers

Biodegradable multiblock poloxamers (BMPs) with gel duration of 8 h to several weeks were prepared by varying their molecular weights from 4000 to 40 000 g mol^?1. The molecular weight of the BMP was controlled by changing the poloxamer to coupling agent ratio. Assuming a micelle packing model of the BMP gel, as in the case of a poloxamer gel, the micelle properties and critical gel concentration of BMPs were investigated on the basis of the scaling concept. The findings suggest that the control of molecular weight by hydrolyzable groups can be a facile approach to optimize the gel properties for biomedical applications. Copyright © 2005 Society of Chemical Industry     

Interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd0.96Zn0.04 Te (211)B substrates by molecular beam epitaxy

Double-crystal x-ray rocking curve (DCRC) and secondary-ion mass-spectroscopy (SIMS) measurements have been performed to investigate the effect of rapid thermal annealing on the interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd_0.96Zn_0.04Te (211)B substrates by molecular beam epitaxy. The sharp satellite peaks of the DCRC measurements on a 100-period HgTe/CdTe (100Å/100Å) superlattice show a periodic arrangement of the superlattice with high-quality interfaces. The negative direction of the entropy change obtained from the diffusion coefficients as a function of the reciprocal of the temperature after RTA indicates that the Hg diffusion for the annealed HgTe/CdTe superlattice is caused by an interstitial mechanism. The Cd and the Hg concentration profiles near the annealed HgTe/CdTe superlattice interfaces, as measured by SIMS, show a nonlinear behavior for Hg, originating from the interstitial diffusion mechanism of the Hg composition. These results indicate that a nonlinear interdiffusion behavior is dominant for HgTe/CdTe superlattices annealed at 190°C and that the rectangular shape of HgTe/CdTe superlattices may change to a parabolic shape because of the intermixing of Hg and Cd due to the thermal treatment.     

Effects of a Nd—Fe—B magnetic filler on the crystallization of poly(phenylene sulfide)

The crystallization of poly(phenylene sulfide) (PPS) in a polymer–magnetic Nd—Fe—B powder suspension was studied. Isothermal crystallization behavior was analyzed by way of differential scanning calorimetry, and the kinetics were described via the Avrami equation. The Avrami parameters and the crystallization times were strongly affected by both the particle size and the presence of a coupling agent coated on the filler particles. The small Nd—Fe—B particles exhibited long induction and half‐times, whereas the large particles tended to have short crystallization times. Particles ranging from 38 to 150 μ appeared to have similar crystallization times and to have no significant change in the value of Avrami index with melt crystallization temperature. As a result of these analyses, the dynamic mechanical properties were determined to correlate the fundamental polymer crystallization characteristics and the physical properties of the PPS binder. The enhancement of the wetting of the filler to the binder was promoted through the coupling agent, as confirmed by dynamic mechanical testing performed on the samples. The storage modulus typically decreased because of the presence of the uncoated small particles. Conversely, the loss modulus was enhanced because of the presence of the coated small particles in the PPS binder. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1091–1102, 2002