A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

A new method to suppress harmonics using /spl lambda//4 bias line combined by defected ground structure in power amplifiers

A new /spl lambda//4 bias line combined by a dumb-bell shaped defected ground structure (DGS) is proposed to suppress harmonics in power amplifiers. The proposed DGS bias line maintains the required high impedance even after DGS is inserted, while the width and length of the /spl lambda//4 bias line are broader and shorter than those of conventional bias lines. When the DGS bias line is used in power amplifiers, the third harmonic components as well as the second harmonic are reduced, because of the increased slow-wave effect over wide harmonic band. It is shown that the reduction of the third harmonic component, the improvement of 1 dB compression point, and power added efficiency are 26.5 dB, 0.45 dB, and 9.1%, respectively.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

Effect of microporosity on tensile properties of as-cast AZ91D magnesium alloy

In the present study, the effect of microporosity on the tensile properties of as-cast AZ91D magnesium alloy was investigated through experimental observation and numerical prediction. The test specimens were fabricated by die-casting and gravity-casting. For gravity-casting, the inoculation and use of various metallic moulds were applied to obtain a wide range of microporosity. The deficiency of the interdendritic feeding of the liquid phase acted as a dominant mechanism on the formation of the micropores in the Mg?Al-alloys, rather than the evolution of hydrogen gas. Although tensile strength and elongation has a nonlinear and very intensive dependence upon microporosity, the yield strength appeared to have a linear relationship with microporosity. However, it was possible to quantitatively estimate the linear contribution of microporosity on the individual tensile property for a range of microporosity, which was below about 1%. The numerical prediction suggests that the effect of microporosity on fractured strength and elongation decreased as the strain hardening exponent increased. Furthermore, the shape and distribution of micropores may play a more dominant role than local plastic deformation on the tensile behavior of AZ91D alloy.     

Observer design for autonomous discrete-time nonlinear systems

We obtain a necessary and sufficient condition for a discrete-time nonlinear system to be locally state equivalent to the nonlinear observer form. The result looks similar to the continuous counterpart except for the fact that Ad-operation is utilized instead of ad-operation.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.     

Design of software systems based on axiomatic design

The ability to utilize fully automated flexible manufacturing systems (FMS) or develop reliable computer-integrated manufacturing (CIM) systems will depend on our ability to develop reliable and reusable software for large complex systems on a timely basis. To date, software design has not gone very far beyond the ad hoc trial-and-error stage. Consequently, the development of software is slow, expensive, unreliable, and unmanageable. The purpose of this paper is to provide a scientific basis for designing software. The approach used here is that of axiomatic design, which is based on two design axioms: the Independence Axiom and the Information Axiom. The axiomatic approach is based on the recognition of the following common elements in design: the existence of independent domains (i.e. the consumer domain, the functional domain, the physical domain, and the process domain); the need to map between various domains during the design process; the decomposition of the characteristic vectors (i.e. functional requirements, design parameters, and process variables) in their respective domains; the zig-zagging required between the domains for decomposition; and the need to satisfy the design axioms during the design process. The axiomatic approach discussed in this paper provides decision making tools for software design in addition to systematic means of knowledge and data representation, synthesis and analysis of software, and the construction of the module-junction structure diagram.     

A probabilistic method for the design of power grounding systems

An improved multivariable, probabilistic method for the safety analysis of power grounding systems is presented. The application of this method is demonstrated in four examples. The first three examples illustrate the practical evaluation of one new and two existing substation grounding grids when the substation is connected to an overhead distribution system. The fourth example ascertains the relative impact of a difference between the S curve of IEC Publication 479 and Dalziel's equation for the allowable body current used in ANSI/IEEE Std 80-1986 on the validity of an exposure model based on the requirements of Std 80. In this example, the statistical data on ground faults have been taken from actual system records. Further possible refinements of the exposure model are discussed