Dynamical modelling of an activated sludge system of a petrochemical plant operating at high temperatures.

The Mexican petrochemical industry, Morelos S.A. de C.V., is one of the biggest and more important petroleum industries in Mexico and Latin America. It has an activated sludge system to treat its wastewater flow, which is approximately 7,000 m3/d. The wastewater contains volatile organic carbon substances classified as toxics. The old surface aeration system was changed for fine bubble diffusers; however, one major drawback of the new aeration system is that the temperature in the bioreactor has increased due to the compression of the air, which at the compressor exit reaches 85 degrees C. This effect results in the temperature in the bioreactor attaining 32 degrees C during the fall, whereas in the spring and summer, the bioreactor temperature reaches higher values than 40 degrees C. The high temperatures reduce the microorganism activity and cause a higher volatilisation rate of volatile compounds, among other effects, which affect the performance of the biological treatment. This work was performed to obtain a better modelling of the wastewater treatment from the petrochemical industry. The model describes the effect of the temperature on the performance of the biological treatment. The model was obtained from tests that were carried out in laboratory reactors with 14 L capacity, which were operated at different temperatures (from 30 to 45 degrees C), with the same wastewater and conditions as the actual system.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

Transmission line routing for reduced external field disturbance

When immersed in a disturbing electromagnetic field, electronic systems are subject to interference due to the energy injected by the external field into the system through the electronic units and, especially, through the transmission lines connecting units one another. The issue of reducing the unwanted energy injection through connecting transmission lines is addressed in this contribution from the point of view of the routing, i.e. of the disposition of the connecting lines that minimizes the injection. The problem is formulated as an optimization problem, dealt with by the simulated annealing minimization technique combined with an efficient way of computing the field coupling to the lines. Results are reported for various cases, and the relation between the characteristics of the interfering field and the efficiency of the reduction is discussed.     

Kaolinite-mullite reaction series: a TEM study

The kaolinite-mullite reaction series in single crystal kaolinite has been characterized by transmission electron microscopy. The exotherm observed at 980° C is attributed to the formation of a spinel phase. Mullite crystallites have also been observed with the spinel phase and both phases have a composition near that of 32 mullite. Subsequent heat treatment leads to the growth of mullite crystallites on the original kaolinite plates with the c-axis perpendicular to the plate.     

Ageing effect on microstructural and mechanical properties of mullite-ZrO2-TiO2 composites

The microstructural and mechanical properties of mullite-zirconia composites with TiO₂ (0.25 and 1.0 mol) additions have been studied, after ageing the samples over a wide temperature range (1000 to 1500° C) for long periods of time (100 to 200 h). In the sample with 0.25 mol TiO₂ addition, changes in mullite composition and in the solid state compatibility at temperatures below 1450° C were detected. In the sample containing 1 mol TiO₂, decomposition of Al₂TiO₅ occurs atT1200° C. Both compositions exhibit no increment in zirconia average grain size during ageing and, concomitantly, there is no strength degradation until higher temperatures (>1400° C) are reached, which become more drastic when Al₂Ti₅ is present.     

Optimal configuration of Energy-Efficient Ethernet

The IEEE 802.3az standard provides a new low power mode that Ethernet network interfaces can use to save energy when there is no traffic to transmit. Simultaneously with the final standard approval, several algorithms were proposed to govern the physical interface state transition between the normal active mode and the new low power mode. In fact, the standard leaves this sleeping algorithm unspecified to spur competition among different vendors and achieve the greatest energy savings. In this paper, we try to bring some light to the most well known sleeping algorithms, providing mathematical models for the expected energy savings and the average packet delay inflicted on outgoing traffic. We will then use the models to derive optimum configuration parameters for them under given efficiency constraints.