Developing an Interactive Spatial Multi-Attribute Decision Support System for Assessing Water Resources Allocation Scenarios

Water Resources Management - In water resource management, assessing water resource allocation scenarios (WRASs) is an important multi-attribute decision making (MADM) problem. It involves...     

Effects of stray magnetic forces on position error signals during a long seeking-and-settling process

This paper is to study how stray magnetic forces encountered in a long seeking process affect position errors of a hard disk drive after it finishes the seek and settles. The study consists of three parts: analysis of stray magnetic forces, numerical modeling, and analysis of numerical results. In the analysis of stray magnetic forces, we lump the stray magnetic forces into three components D1, D2 and D4. Specifically, D1 is a pair of stray magnetic forces in the plane of the voice coil. The two forces act on the two equal legs of the voice coil. In addition, the two forces point to and away from the pivot center, respectively. D2 is a pair of stray magnetic forces out of the plane of the voice coil. The two forces are equal in magnitudes but opposite in directions. The two force components also act on the two equal legs of the voice coil. D4 is identical to D2, except that the two force components in D4 act in the same direction. In the numerical study, we adopt a numerical model that includes a spinning spindle motor, a spinning disk pack with multiple disks, a stationary base plate with a top cover, and a slewing head-stack assembly. Moreover, multiple bearings are present in the model to connect the multiple components. In particular, fluid-dynamic bearings connect the rotating spindle and disk pack with the base plate, pivot bearings connect the base plate with the head-stack assembly, and air bearings connect the spinning disk pack with head sliders located at the tip of the slewing head-stack assembly. Also, the numerical model assumes that the head-stack assembly seeks according to a user-specified seeking profile. Numerical simulations show two major conclusions. First, stray magnetic force component D1 does not lead to significant position errors when the head-stack assembly settles. Stray magnetic force components D2 and D4, however, can affect the position errors by significantly exciting torsion and bending modes of the head-stack assembly. Second, a flex cable can significantly increase position errors below 1 kHz during settling.     

A Case Study on Optimization of Biomass Flow During Single-Screw Extrusion Cooking Using Genetic Algorithm (GA) and Response Surface Method (RSM)

In the present study, response surface method (RSM) and genetic algorithm (GA) were used to study the effects of process variables like screw speed, rpm (x ₁), L/D ratio (x ₂), barrel temperature (°C; x ₃), and feed mix moisture content (%; x ₄), on flow rate of biomass during single-screw extrusion cooking. A second-order regression equation was developed for flow rate in terms of the process variables. The significance of the process variables based on Pareto chart indicated that screw speed and feed mix moisture content had the most influence followed by L/D ratio and barrel temperature on the flow rate. RSM analysis indicated that a screw speed?>?80 rpm, L/D ratio?>?12, barrel temperature?>?80 °C, and feed mix moisture content?>?20% resulted in maximum flow rate. Increase in screw speed and L/D ratio increased the drag flow and also the path of traverse of the feed mix inside the extruder resulting in more shear. The presence of lipids of about 35% in the biomass feed mix might have induced a lubrication effect and has significantly influenced the flow rate. The second-order regression equations were further used as the objective function for optimization using genetic algorithm. A population of 100 and iterations of 100 have successfully led to convergence the optimum. The maximum and minimum flow rates obtained using GA were 13.19?×?10^?7 m³/s (x ₁?=?139.08 rpm, x ₂?=?15.90, x ₃?=?99.56 °C, and x ₄?=?59.72%) and 0.53?×?10^?7 m³/s (x ₁?=?59.65 rpm, x ₂?=?11.93, x ₃?=?68.98 °C, and x ₄?=?20.04%).     

Multi-pressure absorption cycles in solar refrigeration:: A technical and economical study

A technical and economical study of regenerative absorption chillers with multi-pressure cycle has been undertaken as solar operated refrigeration systems. Referred to as advanced absorption chillers they represent one of the new technology options that are under development. Advanced absorption cooling technology offers the possibility of chillers with thermal COPs of 1.5 or greater at driving temperatures of 140°C, which reduces the collector area and the heat rejection requirements compared to current absorption cooling technology. Two different absorption systems have been considered. The first is an advanced, double-effect regenerative absorption cooling system, driven at 140°C, whose efficiency is about 55% of the Carnot efficiency. The second is an ideal, single-effect regenerative absorption system that achieves 70% of the Carnot efficiency driven at 140°C or 200°C. To evaluate the solar performance of a thermally driven chiller requires a separate analysis of the solar availability for a given location compared to the required monthly average solar input. In this analysis different systems, including the vapour compression chillers, have been compared in terms of the thermal and electrical energy input. An effective electrical COP may be computed assuming that the ratio of electrical energy cost to thermal energy cost is four, which is typical of today’s fossil fuel costs. The effective electrical COPs of different technical options can then be compared. Those systems with higher electrical COPs will have lower energy costs. If solar is to be competitive, then the cost of delivered solar thermal energy should be less than the cost of delivered fossil thermal energy.     

Silver nanoparticle films by flowing gas atmospheric pulsed laser deposition and application to surface-enhanced Raman spectroscopy

For the fast uptake into industrial applications, the further development of robust methods of nanomaterials, which are inexpensive and simultaneously technologically feasible, is one of the major key factors. A newly introduced atmospheric pulsed laser deposition method, based on a flowing gas approach, was used for plasmonic metal nanoparticle (NP) film of silver. Contrary to vacuum, in this method, the ambient air restricts expansion of the ablation plume within 1 to 3 mm above the target surface. These sets constrain on the formation of NP film close to the ablation spot. For deposition on a widely spaced surface, ablation material was entrained in a flow of argon, supplied at ~32 ms⁻¹, and effectively delivered to the substrate at ~20 ms⁻¹. The films produced were crystalline and particulate in nature, showing spectral plasmonic feature of surface plasmon resonance in the visible region. The film was directly tested in surface-enhanced Raman spectroscopy for chemical detection of crystal violet; the film with large particulates and aggregated crystallites was well-performed, showing enhanced Raman signals and detection sensitivity. Certainly, flowing gas atmospheric pulsed laser deposition seems a fast alternative to vacuum-pulsed laser deposition but needs further investigations to bring it in the industry for applications in sensor, catalysis, solar cell, and coating technology.     

THERMODYNAMICS OF MOISTURE SORPTION IN ALFALFA PELLETS

ABSTRACT

Experimental data on sorption isotherms of alfalfa pellets were used to determine the thermodynamic functions (differential heat of sorption, spreading pressure, net integral enthalpy and entropy) of the pellets. The thermodynamic functions were then utilized in modeling the specific heats of pellets as a function of moisture content. The estimated values of the thermodynamic functions at different moisture contents confirmed the results of an earlier study on the influence of moisture sorption on the physical integrity of the pellets. The changes in the thermodynamic properties and physical integrity were prominent when the moisture of the pellets were between 0.10 and 0.12 (mass fraction basis). Using the differential heat of sorption, it was determined that alfalfa pellets have higher affinity for moisture uptake when compared to wheat and lentils. The specific heat of the solids of alfalfa pellets had a parabolic relationship with moisture whereas the specific heat of water fraction increased linearly with moisture content of the pellets.     

Effect of CO(2) Enrichment on Synthesis of Some Primary and Secondary Metabolites in Ginger (Zingiber officinale Roscoe)

The effect of two different CO(2) concentrations (400 and 800 μmol mol(-1)) on the photosynthesis rate, primary and secondary metabolite syntheses and the antioxidant activities of the leaves, stems and rhizomes of two Zingiber officinale varieties (Halia Bentong and Halia Bara) were assessed in an effort to compare and validate the medicinal potential of the subterranean part of the young ginger. High photosynthesis rate (10.05 μmol CO(2) m(-2)s(-1) in Halia Bara) and plant biomass (83.4 g in Halia Bentong) were observed at 800 μmol mol(-1) CO(2). Stomatal conductance decreased and water use efficiency increased with elevated CO(2) concentration. Total flavonoids (TF), total phenolics (TP), total soluble carbohydrates (TSC), starch and plant biomass increased significantly (P ≤ 0.05) in all parts of the ginger varieties under elevated CO(2) (800 μmol mol(-1)). The order of the TF and TP increment in the parts of the plant was rhizomes > stems > leaves. More specifically, Halia Bara had a greater increase of TF (2.05 mg/g dry weight) and TP (14.31 mg/g dry weight) compared to Halia Bentong (TF: 1.42 mg/g dry weight; TP: 9.11 mg/g dry weight) in average over the whole plant. Furthermore, plants with the highest rate of photosynthesis had the highest TSC and phenolics content. Significant differences between treatments and species were observed for TF and TP production. Correlation coefficient showed that TSC and TP content are positively correlated in both varieties. The antioxidant activity, as determined by the ferric reducing/antioxidant potential (FRAP) activity, increased in young ginger grown under elevated CO(2). The FRAP values for the leaves, rhizomes and stems extracts of both varieties grown under two different CO(2) concentrations (400 and 800 μmol mol(-1)) were significantly lower than those of vitamin C (3107.28 μmol Fe (II)/g) and α-tocopherol (953 μmol Fe (II)/g), but higher than that of BHT (74.31 μmol Fe (II)/g). These results indicate that the plant biomass, primary and secondary metabolite synthesis, and following that, antioxidant activities of Malaysian young ginger varieties can be enhanced through controlled environment (CE) and CO(2) enrichment.     

Preparation of voltammetric biosensor for tryptophan using multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were grown by chemical vapor deposition. The effect of the composition of carbon paste electrode on its voltammograms was evaluated in basic solution with 5.0×10⁻⁵ M tryptophan (Trp). It was found that addition of MWCNTs to the carbon paste would generate the peak current of Trp because of its catalytic effect on the redox process. The pH strongly affects the peak potential of Trp. The best analytical response was obtained at pH 13.0. The anodic peak currents were proportional to Trp concentrations in the range of 1.0×10⁻⁹−1.0×10⁻⁴ M under the optimized experimental conditions. The detection limit was 2.2×10⁻¹⁰ M. The effect of potential scan rate on the peak potential and peak current of tryptophan was investigated. The correlation of the peak currents against v^1/2 (v is the scan rate) is linear, which is very similar to a diffusion-controlled process. The proposed biosensor was applied to the determination of Trp in pharmaceuticals formulations successfully.     

Photoluminescence emission of nanoporous anodic aluminum oxide films prepared in phosphoric acid

The photoluminescence emission of nanoporous anodic aluminum oxide films formed in phosphoric acid is studied in order to explore their defect-based subband electronic structure. Different excitation wavelengths are used to identify most of the details of the subband states. The films are produced under different anodizing conditions to optimize their emission in the visible range. Scanning electron microscopy investigations confirm pore formation in the produced layers. Gaussian analysis of the emission data indicates that subband states change with anodizing parameters, and various point defects can be formed both in the bulk and on the surface of these nanoporous layers during anodizing.