Effects of genotype and treatment on the antioxidant activity of sweet potato in Taiwan

Six genotypes of sweet potato commercially available in Taiwan, including TNG57, TNG66, TNG68, TYY1, RP and WP, were used as samples in this study of the effects of steaming and kneading with pre-steaming treatments on the antioxidant components and antioxidant properties of methanolic extracts. Steam treatment increased the total phenols contents of all genotypes (2–13 times), flavonoids content of RP (1.3 times) and anthocyanins contents of RP and WP (5–6 times). Steam treatment also increased the reducing power and scavenging DPPH radical effect of sweet potato flours. For the methanolic extracts of steamed and kneaded flours, reducing powers were 0.02–1.70 at 5.0 mg ml⁻¹ and the scavenging effects on DPPH radicals were 19–92% at 2.5 mg ml⁻¹. Both showed the order of RP > WP > TYY1 and TNG66 > TNG57 and TNG68. However, the chelating effect of the six genotypes at 1.0 mg ml⁻¹ ranged from 50% to 73%. Contents of total phenols, flavonoids, and anthocyanins of sweet potato flours were significantly positively correlated with the reducing power and scavenging DPPH radical effects. After steaming and kneading treatments, RP showed the highest increase in the contents of total phenols, flavonoids and anthocyanins among the six genotypes studied.     

Oxygen absorption kinetics in YBa2Cu3Ox

The oxygen absorption process in highly aligned YBa₂Cu₃O_x samples in air and in pure oxygen was studied at several constant temperatures. The process can be expressed in two steps, a chemical reaction controlled step and a diffusion controlled step. The kinetic equations are as follows respectively:

(1 − a_t) ln(1 − a_t) + a_t = k_Dt

The activation energy was calculated using an Arrhenius equation. The technical conditions of heat treatment for oxygen absorption of highly aligned YBa₂Cu₃O_x crystals are discussed.     

A study on the anodic protection of Titanium evaporators in Al2(SO4)3 solution

The feasibility of the anodic protection of titanium evaporators in Al₂(SO₄)₃ solution was studied by the measurement of polarization curves, weight loss, solubility of passive film and AC impedance. The protection parameters and efficiency were determined. In addition, the practical technology of anodic protection was studied by screening reference electrodes and auxiliary cathodes. Throwing power was also measured. Four rows of tube-type evaporators of titanium have been anodically protected in situ. Field tests lasting more than one year show satisfactory results.     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。     

High-T/sub 0/ strain-compensated InGaAsSb-AlGaAsSb quantum-well lasers emitting at 2.43 /spl mu/m

Strain-compensated InGaAsSb-AlGaAsSb quantum-well (QW) lasers emitting near 2.5 /spl mu/m have been grown by solid-source molecular beam epitaxy. The relatively high arsenic composition causing a tensile strain in the Al/sub 0.25/GaAs/sub 0.08/Sb barriers lowers the valence band edge and the hole energy level, leading to an increased hole confinement and improved laser performance. A 60% external differential efficiency in pulsed mode was achieved for 1000-/spl mu/m-long lasers emitting at 2.43 /spl mu/m. A characteristic temperature T/sub 0/ as high as 163 K and a lasing-wavelength temperature dependence of 1.02 nm//spl deg/C were obtained at room temperature. For 2000 /spl times/ 200 /spl mu/m/sup 2/ broad-area three-QW lasers without lateral current confinement, a low pulsed threshold of 275 A/cm/sup 2/ was measured.     

微胞囊技术及产品F-500多功能灭火剂

介绍了微胞囊技术及产品F-500的灭火原理和优势。     

Information analysis of single photon emission computed tomography with count losses

An analysis is presented of the information transfer from emitter-space to detector-space in single photon emission computed tomography (SPECT) systems. The analysis takes into account the fact that count loss side information is generally not available at the detector. Side information corresponds to the number gamma-rays lost deleted due to lack of interaction with the detector data. It is shown that the information transfer depends on the structure of the likelihood function of the emitter locations associated with the detector data. This likelihood function is the average of a set of ideal-detection likelihood functions, each matched to a particular set of possible deleted gamma-ray paths. A lower bound is derived for the information gain due to incorporating the count loss side information at the detector. This is shown to be significant when the mean emission rate is small or when the gamma-ray deletion probability is strongly dependent on emitter location. Numerical evaluations of the mutual information, with and without side information, associated with information-optimal apertures and uniform parallel-hole collimators are presented.     

Study on heat conduction and adsorption/desorption characteristic of MIL-101/few layer graphene composite

Journal of Porous Materials - Aiming at the poor heat conduction performance of porous MIL-101 applied in adsorption cooling process, few layer graphene (FLG) was selected as a promising thermal...     

Cu2O/Cu Cermet as a Candidate Inert Anode for Al Production

Cu₂O/ x Cu ( x =0–25 wt%) cermets were evaluated as a novel partially inert anode for aluminum (Al) production. The physical and mechanical properties, including the compressive strength, flexural strength, thermal expansion coefficient, thermal conductivity, and dc electrical conductivity were tested at room temperature and at temperatures up to 950°C. The coefficient of thermal expansion, compressive strength, flexural strength, thermal conductivity, and electrical conductivity of Cu₂O/Cu cermets increased with increasing Cu content. High-temperature electrical conductivity measurements showed that with increasing temperature, the electrical conductivity increased when the Cu content was below the percolation threshold, while it decreased when the Cu content was above the percolation threshold. A relatively stable CuAlO₂ layer formed on the cermet surface during electrochemical testing, and the corrosion rate of this anode was estimated to be about 1.8–1.9 cm/year in Al production.