Upflow anaerobic sludge blanket (UASB) treatment of supernatant of cow manure by thermal pre-treatment.

Upflow anaerobic sludge blanket (UASB) methane fermentation treatment of cow manure that was subjected to screw pressing, thermal treatment and subsequent solid-liquid separation was studied. Conducting batch scale tests at temperatures between 140 and 180 degrees C, the optimal temperature for sludge settling and the color suppression was found to be between 160-170 degrees C. UASB treatment was carried out with a supernatant obtained from the thermal treatment at the optimal conditions (170 degrees C for 30 minutes) and polymer-dosed solid-liquid separation. In the UASB treatment with a COD(Cr) loading of 11.7 kg/m3/d and water temperature of 32.2 degrees C, the COD(Cr) level dropped from 16,360 mg/L in raw water to 3,940 mg/L in treated water (COD(Cr), removal rate of 75.9%), and the methane production rate per COD(Cr) was 0.187 Nm3/kg. Using wastewater thermal-treated at the optimal conditions, also a methane fermentation treatment with a continuously stirred tank reactor (CSTR) was conducted (COD(Cr) in raw water: 38,000 mg/L, hydraulic retention time (HRT): 20 days, 35 degrees C). At the COD(Cr) loading of 1.9 kg/m3/d, the methane production rate per COD(Cr), was 0.153 Nm3/kg. This result shows that UASB treatment using thermal pre-treatment provides a COD(Cr), loading of four times or more and a methane production rate of 1.3 times higher than the CSTR treatment.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

DETERMINATION OF PALAEOSTRESSES FROM MESOSCALE SHEAR FRACTURES IN CORE SAMPLES USING THE MULTI-INVERSE METHOD

Palaeostress reconstruction is the key to quantitative characterization of fractured hydrocarbon reservoirs. In order to calculate the palaeostresses responsible for fault activity, faults in oriented core samples can be analysed and the optimal stresses can then be determined from fault-slip data in a least-squares sense. Many fractured reservoir rocks, however, include faults generated during a number of different tectonic phases. In these cases, the optimal stresses can be determined for subgroups of faults which are considered to be of approximately the same age. The difficulty with this is that criteria for accurate age-dating are often absent, especially from core samples.
Recently, the so-called "multi-inverse" method has been proposed to address this problem. This is a numerical technique for separating palaeostresses within a heterogeneous fault assemblage in the absence of a priori information on the faults'relative ages. In this paper, we apply the method to eighteen faults in two short (9m) cores from an exploration well in Hokkaido, northern Japan. The cores came from a fractured hydrocarbon reservoir and were oriented by correlation with borehole images. Core lithologies included massive Cretaceous basalts in which there was no layering which would show fault offsets; for these samples, we determined the sense of shear by studying asymmetric microstructures on the fault surfaces. The results show that the rocks have experienced six different stress regimes. In general, these are compatible with the tectonic history of the study area as inferred from the regional stratigraphy and from macroscale geological structures.
These results show that the multi-inverse method can be used to extract palaeostress data from cores, thereby providing information which will assist with the exploration of (and production from) fractured hydrocarbon reservoirs.     

New fault locating system for air-insulated substations usingoptical current detector

The authors present the basic philosophy, construction, design features, and test results of a new fault locating system. This fault locating system helps to shorten the time required for restoration of service after the occurrence of a busbar fault in an air-insulated distribution substation. Recent optical and electronic technologies allow the design of a highly accurate and compact fault locating system which consists of optical current detectors using the Faraday effect and a fault locating processor using a digital data processing technique. The fault location is carried out by discriminating between the directions of zero-sequence currents. Through various tests and field operations, it has been confirmed that the system has sufficient performance for practical applications     

Radiative ignition mechanism of solid fuels

Transmittance of external radiation from a CO₂ laser through a boundary layer of decomposition products over a vertical sample surface is measured during the ignition period. The results indicate that there is significant absorption of the external radiation for PMMA, and a lesser but still not negligible amount, for red oak. An increase in gas phase temperature over surface temperature is observed over much of the ignition interval. Using the experimentally measured incident flux at the sample surface, surface temperature history was calculated from a model that included re-radiation and convection losses from the surface, endothermic decomposition and conduction into the material. The results confirm the significant effect of gas phase absorption on surface temperature. Steady-state-derived surface regression rate expression was used for PMMA in this model. The results raise questions about the validity of such data for the dynamic heating conditions during the ignition period. Further studies needed to understand the radiative ignition mechanism are identified.     

Solid-Phase Syntheses of Two Deacetyl-Thymosin β4 Analogues with Substitution at Position 12 and Their Effects on Impaired Blastogenic Response of T Lymphocytes of Uremic Patients

Two deacetyl-thymosin β₄ analogues containing Phe(4Br) or D-Phe(4Br) as position 12 were synthesized by the manual solid-phase method, and their immunological effects on the impaired blastogenic response of phytohemagglutinin-stimulated T lymphocytes of uremic patients with infectious diseases were studied. Bromination of the p-position of Phe¹² resulted in a marked restorative effect on the impaired blastogenic response of T lympocytes compared with that of our synthetic deacetyl-thymosin β₄ The synthetic [Phe(4Br)¹²]deacetyl-thymsin β₄ was approximately equal in potency to our synthetic [Phe(4F)¹²]deacetyl-thymosin β₄ in uremic patients, but the other analogue, [D-Phe(4Br)¹²]deacetyl-thymosin β₄, had no effect.     

Diffuse pollution in Japan: issues and perspectives.

Many parts of Japan have experienced rapid urbanization and industrialization over the past 50 years. This trend resulted in severe water pollution in many urban areas. To address the pollution problems, several measures such as construction of sewerage systems and enactment of laws and regulations have been undertaken. Because of these measures, the water quality has been improved to some extent. However, many water quality concerns still remain and are attributed in part to diffuse pollution. In this paper, historical progress, present situation and future aspects of diffuse pollution problems in Japan are reviewed. It is noted that solving diffuse pollution problems will require a combination of several measures including application of conventional treatment technologies and natural purification systems, implementation of appropriate policy measures, and promotion of citizen participation.     

Hydroliquefaction of low-sulfur coals using iron carbonyl complexes—Sulfur as catalysts

Hydroliquefaction of low-sulfur Australian coals (Wandoan and Yallourn) was studied using iron carbonyl complexes as catalyst. The addition of Fe(CO)₅ (2.8 wt% Fe of coal) increased coal conversion from 48.6 to 85.2% for Wandoan coal, and from 36.7 to 69.7% for Yallourn coal in 1-methylnaphthalene at 425°C under an initial hydrogen pressure of 50 kg cm^?2. When molecular sulfur was added to iron carbonyls (Fe(CO)₅, Fe₂(CO)₉ and Fe₃(CO)₁₂), higher coal converions ( > 92%) and higher oil yields (>46%) were obtained, along with an increase in the amount of hydrogen transferred to coal from the gas phase (0.2 to 2.8%, d.a.f. coal basis). In the liquefaction studies using a hydrogen donor solvent, tetralin, Fe(CO)₅S catalyst increased the amount of hydrogen absorbed from the gaseous phase and decreased the amount of naphthalene dehydrogenated from tetralin. The direct hydrogen transfer reaction from molecular hydrogen to coal fragment radicals seems to be a major reaction pathway. Organic sulfur compounds, dimethyldisulfide and benzothiophene, and inorganic FeS₂ and NiS were found to be good sulfur sources to Fe(CO)₅. From X-ray diffraction analyses of liquefaction residues, it is concluded that Fe(CO)₅ was converted into pyrrhotite (Fe_1?xS) when sulfur was present, but into Fe₃O₄ in the absence of sulfur.     

High-reliability GaAs-AlGaAs HBTs by MBE with Be base doping andInGaAs emitter contacts

The authors have developed a modified MBE growth process to produce high-gain n-p-n GaAs-AlGaAs heterojunction bipolar transistors (HBTs) with a mean time to failure (MTTF) of 1.5×10⁸ h at 125°C. Beryllium incorporation and diffusion are controlled through a combination of reduced substrate temperature and increased As/Ga flux ratio during MBE growth, resulting in extremely stable HBT profiles. The authors also demonstrate graded InGaAs surface layers with nonalloyed refractory metal contacts that significantly improve ohmic reliability compared to alloyed AuGe contacts. The ability to produce robust HBTs by MBE is critically important to this technology