Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Surface-Chemical Criteria for Optimum Adhesion

According to Bikerman, who attributes failure in adhints to a weak boundary layer, it is almost impossible and meaningless to correlate adhesive strength to surface-chemical properties of adhints. Though his assertion seems to be confirmed by the recent studies of Schonhorn and his coworkers on the methods of CASING and TCR, not a few results have yet been accumulated, which show a close relation between them. In this paper surface-chemical criteria for the optimum adhesion are investigated and the minimum interfacial tension or the maximum wetting pressure is deduced from the published data and our own as a first approximation. It is emphasized that, when critical surface tension γ_c would be used as a measure of surface-chemical properties of solid, its variability according to liquid series (nonpolar, polar and hydrogen bonding liquids) should be carefully taken into consideration. The importance is shown for polyethylene and its fluorine substituted polymers, using newly measured contact angle data and Zisman's data. Results of Levine et al. and Schonhorn et al. on adhesive shear strength with epoxy adhesives are replotted against available values of γ_c obtained by the use of hydrogen bonding liquid (γ_c^c), which are thought to reflect wetting behaviors of epoxy adhesives quite well. Each curve shows a maximum around γ_c^c = 40 dyne/cm with few points falling off the curves.     

Psychological Stress Exacerbates Inflammation of the Ileum via the Corticotropin-Releasing Hormone-Mast Cell Axis in a Mouse Model of Eosinophilic Enteritis

The effects of psychological stress on eosinophilic gastrointestinal disorders have not been elucidated. This study investigated the effects of psychological stress in a mouse model of eosinophilic enteritis (EoN). BALB/c mice were treated with ovalbumin (OVA) to create an EoN model and subjected to either water avoidance stress (WAS) or sham stress (SS). Microscopic inflammation, eosinophil and mast cell counts, mRNA expression, and protein levels of type 2 helper T cell (Th2) cytokines in the ileum were compared between groups. We evaluated ex vivo intestinal permeability using an Ussing chamber. A corticotropin-releasing hormone type 1 receptor (CRH-R1) antagonist was administered before WAS, and its effects were analyzed. WAS significantly increased diarrhea occurrence and, eosinophil and mast cell counts, and decreased the villus/crypt ratio compared to those in the SS group. The mRNA expression of CRH, interleukin IL-4, IL-5, IL-13, eotaxin-1, and mast cell tryptase β2 significantly increased, and the protein levels of IL-5, IL-13, and OVA-specific immunoglobulin E (IgE) also significantly increased in the WAS group. Moreover, WAS significantly increased the intestinal permeability. The CRH-R1 antagonist significantly inhibited all changes induced by WAS. Psychological stress exacerbated ileal inflammation via the CRH-mast cell axis in an EoN mouse model.     

Bone Tissue Engineering in Rat Calvarial Defects Using Induced Bone-like Tissue by rhBMPs from Immature Muscular Tissues In Vitro

This study aimed to induce bone-like tissue from immature muscular tissue (IMT) in vitro using commercially available recombinant human bone morphogenetic protein (rhBMP)-2, rhBMP-4, and rhBMP-7, and then implanting this tissue into a calvarial defect in rats to assess healing. IMTs were extracted from 20-day-old Sprague-Dawley (SD) fetal rats, placed on expanded polytetrafluoroethylene (ePTFE) with 10 ng/μL each of rhBMP-2, BMP-4, and BMP-7, and cultured for two weeks. The specimens were implanted into calvarial defects in 3-week-old SD rats for up to three weeks. Relatively strong radiopacity was observed on micro-CT two weeks after culture, and bone-like tissue, comprising osteoblastic cells and osteoids, was partially observed by H&E staining. Calcium, phosphorus, and oxygen were detected in the extracellular matrix using an electron probe micro analyzer, and X-ray diffraction patterns and Fourier transform infrared spectroscopy spectra of the specimen were found to have typical apatite crystal peaks and spectra, respectively. Furthermore, partial strong radiopacity and ossification were confirmed one week after implantation, and a dominant novel bone was observed after two weeks in the defect site. Thus, rhBMP-2, BMP-4, and BMP-7 differentiated IMT into bone-like tissue in vitro, and this induced bone-like tissue has ossification potential and promotes the healing of calvarial defects. Our results suggest that IMT is an effective tissue source for bone tissue engineering.     

Removal of Interlayer Water of two Ti3C2Tx MXenes as a Versatile Tool for Controlling the Fermi-Level Pinning-Free Schottky Diodes with Nb:SrTiO3

Striving for the sixth-generation communication technology discovery, semiconductors beyond Si with wider bandgaps as well as non-conventional metals are actively being sought to achieve high speeds whilst maintaining devices miniaturization. 2D materials may provide the potential for downsizing, but their functional advantage over existing counterparts still longs to be discovered. Along that path, surface-adsorbed or bulk-intercalated water molecules remaining after wet-chemical synthesis of 2D materials are generally seen as obstacles to high-performance achievement. Herein, the control of such water within the interlayers of solution-processed metallic 2D titanium carbide (MXene) by vacuum annealing duration is demonstrated. Moreover, the impact of water removal on work function (WF) and functional terminations is unveiled for the first time. Furthermore, the usefulness of such water for controlling a novel Schottky diode in contact with an n-type oxide semiconductor, niobium-doped strontium titanate (Nb:SrTiO₃) is observed. The advantage of MXene compared to conventional gold as facile processing, WF tunability, and lower turn-on voltage in the Schottky anode application is highlighted. This fundamental study shows the way for a novel Schottky diode preparation in atmospheric conditions and provides implications for further research directions aiming at commercialization.     

A high-precision low-voltage bipolar current mirror circuit and its compensation for stability

A current mirror circuit is widely utilized as an important building block in analogue signal processing circuits. This paper describes a high-precision low voltage bipolar current mirror circuit. Well known current mirror circuits, such as a simple current mirror and a Wilson current mirror, have a trade-off between low-voltage operation and accuracy of the current gain. The accuracy of the proposed current mirror is high in spite of low current amplification factor (β) of transistors and large current output (or a large number of the multiple output). The current mirror circuit can operate at a 1V or less supply voltage. The high accuracy is realized by negative current feedback with high gain. Thus, the stability of the circuit and compensation methods are discussed. PSPICE simulation shows that the proposed current mirror circuit compensated using Miller components composed of a capacitor and a resistor is stable and can operate at a 1V supply voltage.     

Selective Determination of Dopamine on a Boron‐Doped Diamond Electrode Modified with Gold Nanoparticle/Polyelectrolyte‐coated Polystyrene Colloids

Negatively charged gold nanoparticles (AuNPs) and a polyelectrolyte (PE) have been assembled alternately on a polystyrene (PS) colloid by a layer‐by‐layer (LBL) self‐assembly technique to form three‐dimensional (Au/PAH)₄/(PSS/PAH)₄ multilayer‐coated PS spheres (Au/PE/PS multilayer spheres). The Au/PE/PS multilayer spheres have been used to modify a boron‐doped diamond (BDD) electrode. Cyclic voltammetry is utilized to investigate the properties of the modified electrode in a 1.0 M KCl solution that contains 5.0 × 10^?3 M K₃Fe(CN)₆, and the result shows a dramatically decreased redox activity compared with the bare BDD electrode. The electrochemical behaviors of dopamine (DA) and ascorbic acid (AA) on the bare and modified BDD electrode are studied. The cyclic voltammetric studies indicate that the negatively charged, three‐dimensional Au/PE/PS multilayer sphere‐modified electrodes show high electrocatalytic activity and promote the oxidation of DA, whereas they inhibit the electrochemical reaction of AA, and can effectively be used to determine DA in the presence of AA with good selectivity. The detection limit of DA is 0.8 × 10^?6 M in a linear range from 5 × 10^?6 to 100 × 10^?6 M in the presence of 1 × 10^?3 M AA.     

Heat transfer enhancement in duct with blunt body inserted close to its wall

This paper shows the effects of clearance length between a body and a duct wall, and duct height on the heat transfer characteristics and flow behavior at a downstream region of the body when a blunt body was set in a parallel plate duct with some distance separating it from the duct wall as a turbulence promoter. For the ratio of clearance to body height, C/D = 0.05–01, the heat transfer was characterized by the reattachment of shear flow separated from the body. Furthermore, the heat transfer depended on both the reattachment flow and the separation vortex at C/D = 0.15–0.2, and the side vortex induced by Karman vortex at C/D = 0.25–0.275 was also observed. We found the reattachment flow gives a superior effect to enhance heat transfer at a low Reynolds number, but at a larger Reynolds number, the side vortex induced by Karman vortex becomes more effective to heat transfer enhancement. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(5): 336–349, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20067     

Stabilization effect of Co for Mo phase in CoMoAl2O3 hydrodesulfurization catalysts studied with X-Ray photoelectron spectroscopy

The promotional effects of Co in $\text{CoMo}\text{Al}{}_2\text{O}{}_3$ hydrodesulfurization (HDS) catalysts were studied by means of X-ray photoelectron spectroscopy. The higher MoO₃-content $\text{Mo}\text{Al}{}_2\text{O}{}_3$ catalysts (10 and 20 wt% MoO₃) contain mobile Mo, which migrates from the pores to the outermost surface layers of the catalysts and segregates to form less active crystalline MoS₂ during the HDS reaction, while in the case of $\text{Mo}\text{Al}{}_2\text{O}{}_3$ (5 wt% MoO₃) catalyst: no migration of Mo was observed. It is revealed that the Co in $\text{CoMo}\text{Al}{}_2\text{O}{}_3$ catalyst inhibits the migration and segregation of Mo and that it keeps Mo effective for the HDS reaction, since no surface enrichment of Mo was observed. It is concluded that stabilization of the Mo monomolecular layer is the main role of Co. The active species of Mo is suggested to have the composition of S/Mo(IV) = 1 on the basis of the sulfur contents of the catalysts under the mild HDS reaction conditions.     

Estimation of the Surface Energy of Polymer Solids

The methods to estimate the surface tension of polymer solids using contact angles have been reviewed in the first part. They are classified into the following three groups depending on the theories or the equations applied: (1) the methods using the Young's equation alone, (2) the methods using the combined equation of Young and Good-Girifalco, and (3) the methods using the equations of work of adhesion. Some notes and comments are given for each method and results are compared with each other. The two-liquids method for rather high energy surface is also introduced.

Next, some new possibilities to evaluate the surface tension of polymer solids are presented by our new contact angle theory in consideration of the friction between a liquid drop and a solid surface. The advancing and receding angles of contact (θ _a and θ _r ) are explained by the frictional tension γ_F and accordingly two kinds of the critical surface tension γ_C (γ_Ca and γ_Cr ) are given.

This work has shown that one of the recommendable ways to evaluate γ_S is either the maximum γ_LV cos θ_a or the maximum γ_C using the advancing contact angle θ_a alone, and another way is the arithmetic or the harmonic mean of the γ_Ca and γ_Cr . A depiction to determine the γ_C such as ln(1 + cos θ₀ ) vs. γ_LV with cos θ₀ = (cos θ₀ + cos θ_r )/2 has also been proposed.