Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Hydrogen absorption by Pd-coated ZrNi prepared by using Barrel-Sputtering System

To improve the durability of hydrogen storage materials against surface poisoning by impurity gases, effectiveness of Pd-coating layer prepared by using a Barrel-Sputtering System was examined for ZrNi powder. The effectiveness of Pd-coating was evaluated by activation temperature, at which Pd/ZrNi poisoned by air could be activated to absorb hydrogen. Characterization of Pd-coated ZrNi (denoted as Pd/ZrNi) by scanning electron microscopy, electron probe microanalysis and X-ray diffraction showed that a uniform Pd-coating layer was formed with the barrel-sputtering system. It was found that the poisoned Pd/ZrNi sample could be activated even at 423 K to absorb hydrogen at room temperature. This exhibits remarkable contrast to bare ZrNi, which could be only activated appreciably above 1073 K. It is concluded that the Pd-coating by barrel sputtering is quite effective to avoid the effect of surface poisoning of powdery hydrogen storage materials. However, the activation at excessively high temperature resulted in the loss of high activity to absorb hydrogen. It was concluded that this phenomenon was associated with reactions between Pd and ZrNi to form PdZr and other byproducts.     

Numerical analyses of high‐beta spherical tokamaks with varied elongation

The effect of plasma elongation on the second‐stable spherical tokamak (ST) was numerically studied using the experimentally measured pressure and current profiles of ultrahigh‐beta STs. The maximum beta of ST over 50% was obtained in the TS‐3 ST/CT experiment by applying an external toroidal field to an FRC. It was found that the marginal beta for the ballooning instability increased with the plasma elongation κ of ST. The elongated STs with κ > 2 have the magnetic shear (S)–pressure gradient (α) profiles located in the second‐stable regime for the ballooning mode and the stability margin increased with κ. The close relation between the absolute minimum‐B profile and the second stability was documented. The effect of elongation on maximum beta was observed to saturate when κ exceed 3, indicating that the optimized elongation for high‐beta STs is located around 2 < κ < 3. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 1–6, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20132     

Effects of Working Fluid,Tubeside Enhancement and Bundle Depth on the Optimized Fin Geometry of a Horizontal Condenser Tube

A theoretical study has been made to optimize the fin geometry of a horizontal finned tube which is to be usedfor condensers that handle the vapor load of a liquid phase change cooling module.Systematic numerical calcu-lations of the vapor to coolant heat transfer have been performed for parametric values of fin height,fin spacing,vertical bundle depth and tubeside heat transfer coefficient.Three dielectric fluids (R-113,FC-72,and FC-87)at atmospheric pressure were selected as the working fluids.For a single tube with optimized fin geometry,theaverage heat flux increased in the order of FC-87,R-113 and FC-72.Both the optimum fin height and optimumfin spacing increased with increasing vertical bundle depth.     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Studies on calcium antagonistic and alpha 1-adrenergic receptor blocking activities of monatepil maleate, its metabolites and their enantiomers

The calcium antagonistic and alpha 1-adrenergic receptor blocking activities of monatepil maleate (CAS 103377-41-9, (+/-)-N-(6,11-dihydrodibenzo [b, e] thiepin-11-yl) -4-(4-fluorophenyl)-1-piperazinebutanamide monomaleate, AJ-2615), a novel calcium antagonist, its metabolites and their enantiomers were studied in vitro. Monatepil maleate inhibited calcium-induced contractions of rat thoracic aorta (pA2 = 8.71) and l-phenylephrine-induced contractions of rabbit superior mesenteric artery (IC50 = 56.6 nmol/l). The calcium antagonistic activities of the metabolites of monatepil maleate (AJ-2615-sulfoxide A, AJ-2615-sulfoxide B and AJ-2615-sulfone) were 1/10 of that of monatepil maleate. However, their alpha 1-adrenergic receptor blocking activities were similar to or slightly more potent than that of monatepil maleate. The potencies of the calcium antagonistic activities of monatepil maleate and its enantiomers [(S)-AJ-2615 and (R)-AJ-2615] were in the order of (S)-AJ-2615 > monatepil maleate > (R)-AJ-2615 whereas no difference was observed among them in alpha 1-adrenergic receptor blocking activity. In calcium antagonistic and alpha 1-adrenergic receptor blocking activities, there was no difference between the enantiomers of monatepil maleate metabolites. In conclusion, there was a difference with several times in calcium antagonistic activity between the two enantiomers of monatepil maleate but not in their alpha 1-adrenergic receptor blocking activity.