Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

L－B膜修饰电极循环伏安行为模拟──（Ⅰ）电荷转移速度常数对循环伏安性能的影响

本文用计算机数字模拟方法研究了电活性分子多层Ｚ型Ｌ－Ｂ膜修饰电极的循环伏安行为。计算了电极与修饰Ｌ－Ｂ膜分子第一层之间的电荷转移速度常数Ｋ_ｏ，Ｌ－Ｂ膜分子层间的电荷转移速度常数ｋ_ｉ；对峰电位差△Ｅ_ｐ及阳极峰面积Ｑ的影响，以及在不同条件下各层分子的氧化态分数随扫描时间的变化。为研究和设计电活性分子修饰电极的实际体系提供了大量数据和信息。     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

The use of doped polyaniline as an electrode in the galvanic anodic protection of ferrous metals in industrial acid solutions

In order to investigate the galvanic anodic protection (GAP) of ferrous metals (such as 410, 304 and 316 stainless steels) in acid solutions by doped polyaniline (PANi), separate doped PANi powder-pressed electrodes with different surface areas (the area ratio of the PANi electrode to stainless steel is between 1:1 and 1:2) have been prepared. These were coupled with ferrous metal in the following solutions: 5 M sulphuric acid, 5 M phosphoric acid and industrial phosphoric acid (containing 5 M phosphoric acid and 0.05% chloride ion) to construct a galvanic cell, in which PANi is cathode while ferrous metal is anode. The results indicate that a PANi electrode with sufficient area can provide corrosion protection to stainless steel in these acidic solutions. A pilot scale coupling experiment was carried out. The results indicate that PANi is a promising material as an electrode for the anodic protection of ferrous metals in acidic solutions in industrial situations.     

单光子时间分辨在线谱仪系统中的接口电路

本文介绍单光子时间分辨在线谱仪系统中的多道分析器与IBM PC/XT微型计算机接口的工作原理及控制程序。     

Constrained Drying of Aqueous Yttria-Stabilized Zirconia Slurry on a Substrate. I: Drying Mechanism

Aqueous yttria-stabilized zirconia slurry was cast on a substrate to form wet coatings. Both weight loss and thickness reduction were measured, during the drying process. Lateral drying was observed by in situ monitoring of the coating surface. The drying kinetics were classified as an initial constant rate period (CRP), followed by a falling rate period (FRP). Thickness reduction occurred in the CRP stage, and was uneven across the coating because of lateral flow. As tensile stresses developed within the coating because of the constrained volume shrinkage, crack formation and propagation occurred in the FRP stage and affected the drying rate.     

推力矢量控制技术在导弹上的应用及发展

简要介绍了推力矢量控制技术的概念,分析了推力矢量控制的基本原理及特点.在简要分析其技术发展历程的基础上,给出了导弹推力矢量技术的现状和发展趋势.     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

液态金属钠高温沸腾实验回路应力分析与强度计算

本文主要完成了液态金属钠高温沸腾实验回路的应力分析与计算，确定了回路高温区连接管系的布置型式和支吊架系统，是该回路总体设计的重要组成部分。