A new lateral MOS-gated thyristor with controlling base-current

A new lateral MOS-gated thyristor, called the Base-Current-Controlled Thyristor, is described. This device is designed so that most holes at the on-stage reach the P base through the floating P⁺ region adjacent to the P base and the on-state MOSFET. At the turn-off stage, the interruption of the hole current to the P base due to switching off the above MOSFET occurs simultaneously with the conventional turn-off operation. The concept of this device is verified experimentally by using the fabricated lateral device with the external MOSFET. This device exhibits a better trade-off relation between the on-state voltage and the turn-off time compared uith the conventional MOS-gated thyristor     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Effects of crystallographic misorientation on power loss in

The effects of the inclination angle β of the [001] axis out of the sheet plane on the thickness dependence of the power losses in     

The effects of R-75,317 on antiglomerular basement membrane glomerulonephritis in rats

Platelet-activating factor (PAF) is a potent inflammatory mediator which is released by various inflammatory cells and produced by certain tissues, including the kidney. PAF has been shown to increase glomerular permeability to protein and to decrease glomerular filtration rate (GFR) by contracting mesangium. On the basis of these observations, it has been suspected that PAF may play a role as mediator of glomerular damage in glomerular nephritis. To examine this possibility, we studied the effects of a specific PAF antagonist, R-75,317, on the development of an experimental model of anti-glomerular basement membrane (anti-GBM) glomerulonephritis. Glomerulonephritis was initiated by injecting rabbit anti-rat GBM serum into rats. Proteinuria gradually developed after serum injection, plateaued at week 2, and remained at the high level of week 2 throughout the experimental period (6 wk). Chronic treatment with R-75,317 (10 mg/kg/day i.p.) tended to delay the onset of proteinuria and significantly accelerated the recovery phase. Creatinine clearance (Ccr) fell to 40% at week 3. R-75,317 treatment completely prevented this decline of Ccr. Histological changes in this model (glomerular hypertrophy, proliferation of mesangial matrix and interstitial fibrosis) were also ameliorated by the R-75,317 treatment. The results suggest that PAF may play a role in the development of glomerulonephritis and that PAF antagonists could be used in the treatment of human renal disease. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, May 1989.     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

On the accuracy and efficiency of substrate current calculationsfor sub-μm n-MOSFET's

The accuracy and efficiency of the self-consistent (regarding the electric field) Monte Carlo model, nonself-consistent Monte Carlo model, and the soft-threshold lucky electron model (LEM) for the calculation of substrate currents in deep sub-μm n-MOSFET's are investigated. While the two Monte Carlo models are in good agreement with the experiment, the simpler LEM model still gives reasonable results even for a 0.16 μm n-MOSFET. On the other hand, huge differences in the CPU time consumption are found and the LEM is about four orders of magnitude faster than the self-consistent Monte Carlo simulations. The nonself-consistent calculations are only one order of magnitude slower than the LEM. The good agreement with the experiment is obtained without considering the so-called surface impact ionization or any fitting of parameters on the device level     

Effect of crystallization and interface formation mechanism on mechanical properties of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate

A previous study has shown that the adhesion between the film and substrate of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate was evident with the increases in barrel temperature and injection holding pressure. In this second part of the research work, the crystallinity at the interfacial region (i.e., region between the film and the injected substrate) was extensively studied using FTIR imaging, polarized light microscopy, and DSC in an attempt to determine the level of influence that crystallinity has on the interface and bulk mechanical properties. Consequently, a more thorough and clearer picture of the influence of the inserted film on the interfacial crystallinity and subsequently the substrate mechanical properties, such as peel strength and impact strength, has been revealed. The initial proposition that crystallinity could enhance film–substrate interfacial bonding has been confirmed, judging from the higher peel strength with increasing crystallinity at the interfacial region. Nevertheless, the change in crystallinity was not only confined to the interfacial region. With the film acting as heat‐transfer inhibitor between the injected resin and the mold wall, the total crystal structure of the substrate was substantially altered, which subsequently affected the bulk mechanical properties. The lower impact strength of film‐insert injection‐molded samples compared to that of samples without film inserts provided evidence of how the film could impart inferior properties to the substrate. The difference in cooling rate between the substrate and film might also cause other defects such as warpage and/or residual stress build‐up within the product. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 294–301, 2005     

Ring-opening polymerization of 2-oxazolines initiated by chloromethyl groups introduced onto carbon black surface

Summary The ring-opening polymerization of 2-oxazolines (OXZs) was found to be initiated by chloromethyl groups introduced onto carbon black surface. The introduction of chloromethyl groups onto the surface was achieved by the reaction of carbon black with 3,3-bischloromethylbenzoyl peroxide in carbon tetrachloride. During the polymerization, poly-OXZs were grafted from carbon black based on the propagation of the polymers from the surface: percentage of grafting increased with an increase of conversion and reached 40–60%. The polymerization was accelerated by the addition of potassium iodide. Poly-OXZ-grafted carbon black produced stable colloidal dispersions in both hydrophobic and hydrophilic solvents.     

Synthesis mechanism of titanium carbide nano-fiber during self-propagating high temperature synthesis

Titanium carbide nano-fiber was synthesized by self-propagating high temperature synthesis (SHS) method. The final products after the SHS reaction were titanium carbide containing excess carbon and metallic titanium, which were removed by additional leaching process. TEM observation revealed that the average diameter is about 20 nm. Neutron diffraction analysis was carried out to study non-stoichiometric number of the titanium carbide. The non-stoichiometric numbers of the titanium carbide were 0.89–0.94. The Rietveld refinement of each patterns converged to good agreement (÷2=0.49–1.34). The formation mechanism of the carbide is related to a liquid-solid reaction including the preferential diffusion process of carbon atom into liquid titanium. This article is based on a presentation made in the 2002 Korea-US symposium on the “Phase Transformations of Nano-Materials,” organized as a special program of the 2002 Annual Meeting of the Korean Institute of Metals and Materials, held at Yonsei University, Seoul, Korea on October 25–26, 2002.