Sintering studies of nano-crystalline zinc oxide

Sintering and grain growth of nano-crystalline undoped ZnO has been studied in detail over a wide range of temperature and holding time. Below 800 °C, sintering of over 70% theoretical density is not observed, irrespective of particle size. At 900 °C for 6 h, the nano-crystalline sample sinters to 99% of theoretical density whereas the density for as received sample is 93% of theoretical density. However, at 1300 °C or higher, the densification is found to be much faster and after a few hours becomes independent of holding time. Grain growth studies reveal a similar feature of attaining saturation over holding time. The average saturated grain size is found to be ∼1.5 and ∼2.2 μm at 800 and 900 °C, respectively, while at 1300 °C or higher, it is in between 12 and 13 μm.     

Network and device-level impacts: performance and reliability of active I/O storage systems

Distributed active storage architectures are designed to offload user-level processing to the peripheral from the host servers. In this paper, we report preliminary investigation on performance and fault recovery designs, as impacted by emerging storage interconnect protocols and state-of-the-art storage devices. Empirical results obtained using validated device-level and interconnect data demonstrate the significance of the said parameters on the overall system performance and reliability.     

Microarchitectures for Managing Chip Revenues under Process Variations

As transistor feature sizes continue to shrink intothe sub-90nm range and beyond, the effects of process variationson critical path delay and chip yields have amplified. A commonconcept to remedy the effects of variation is speed-binning, bywhich chips from a single batch are rated by a discrete range offrequencies and sold at different prices. In this paper, we discussstrategies to modify the number of chips in different bins andhence enhance the profits obtained from them. Particularly, wepropose a scheme that introduces a small Substitute Cacheassociated with each cache way to replicate the data elementsthat will be stored in the high latency lines. Assuming a fixedpricing model, this method increases the revenue by as much as13.8% without any impact on the performance of the chips.     

High voltage 4H-SiC Schottky barrier diodes

Characteristics of 4H-SiC Schottky barrier diodes with breakdown voltages up to 1000 V are reported for the first time. The diodes showed excellent forward I-V characteristics, with a forward voltage drop of 1.06 V at an on-state current density of 100 A/cm². The specific on-resistance for these diodes was found to be low (2×10 ^-3 Ω-cm² at room temperature) and showed a T ^1.6 variation with temperature. Titanium Schottky barrier height was determined to be 0.99 eV independent of the temperature. The breakdown voltage of the diodes was found to decrease with temperature     

Breakdown Trade-Off Relation of Mechanical Properties via Micro-alloying in Mg–Mn Alloys

The impact of micro-alloying on tensile behavior at strain rates in various ranges is examined using five types of extruded Mg-0.3 at. pct Mn–0.1 at. pct X ternary alloys, where X is selected as a common element, Al, Li, Sn, Y or Zn. Microstructural observations reveal that the average grain size of these extruded alloys is between 1 and 3 μm, and these micro-alloying elements segregate at grain boundaries. In room temperature tensile and compression tests, these results show that the mechanical properties and deformation behavior are influenced by the micro-alloying element, even as a small addition of 0.1 at. pct. Mg–Mn–Y and Mg–Mn-Zn alloys show higher strength and smaller strain rate sensitivity (m-value) among the present alloys, owing to the rate-controlling mechanism as dislocation slip. On the other hand, the Mg–Mn–Li alloy exhibits the largest elongation to failure in tension and the highest strain rate sensitivity, associated with high contribution of grain boundary sliding to deformation. These differences are due to the grain boundary segregation of the micro-alloying elements. Compared to the common Mg alloys, the present ternary alloys also show a trade-off relationship between strength and ductility, which is similar to that of the well-known Mg alloys; however, these properties of the Mg–Mn system ternary alloys could be controlled via the type of micro-alloying elements with a chemical content of 0.1 at. pct.

     

A hybrid evolutionary approach to the registration area planning problem

The last two decades have witnessed a phenomenal growth in the number of cellular wireless network users which in turn stressed the need to utilize the limited network bandwidth in an efficient manner. The network bandwidth is consumed not only by user traffic, but also by control traffic needed for ensuring the mobility of users. As we don’t have any control over the volume of user traffic, all attempts to efficiently use bandwidth are based on frequency reuse and minimizing the control traffic. The registration area planning (RAP) problem seeks a partition of the cells of the network into contiguous areas called registration areas so that the bandwidth consumed by control signals is minimized. RAP problem in an \(\mathcal {NP}\) -Hard problem. In this paper, we present a steady-state grouping genetic algorithm with local search to solve this problem. We have compared our approach with the state-of-the-art approaches reported in the literature. Computational results show the effectiveness of our approach.     

Formation of Nanocrystalline Calcia by the Decomposition of Calcite

Formation of nanocrystalline calcia from calcite has been studied in situ via transmission electron microscopy. The crystallographic transformation occurred via two mechanisms: the first is by distortion of the cleaved rhombohedron of calcite, formed by {104} planes in hexagonal coordinates, into a cube. This produced a microstructure of oriented, elongated nanocrystals of calcia with planar boundaries. In the second mechanism, the micrometer-sized parent calcite particles broke up into nano-sized grains as the decomposition began, leading to irregularly shaped, randomly oriented nanocrystals of calcia.     

Evaluation of AMSR-E soil moisture results using the in-situ data over the Little River Experimental Watershed, Georgia

An operational global soil moisture data product is currently generated from the observations of the Advanced Microwave Scanning Radiometer (AMSR-E) aboard NASA's Aqua satellite using the retrieval procedure described in Njoku and Chan [Njoku, E.G. and Chan, S.K., 2006. Vegetation and surface roughness effects on AMSR-E land observations, remote sensing environment, 100(2), 190-199]. We have generated another soil moisture dataset from the same AMSR-E observed brightness temperature data using the Land Surface Microwave Emission Model (LSMEM) adopting a different estimation method. This paper focuses on a comparison study of soil moisture estimates from the above two methods. The soil moisture data from current AMSR-E product and LSMEM are compared with the in-situ measured soil moisture datasets over the Little River Experimental Watershed (LREW), Georgia, USA for the year 2003. The comparison study was carried out separately for the AMSR-E daytime and night time overpasses. The LSMEM method performed better than the current operational AMSR-E retrieval algorithm in this study. The differences between the AMSR-E and LSMEM results are mostly due to differences in various simplifications and assumptions made for variables in the radiative transfer equations and the soil and vegetation based physical models and the accuracy of the input surface temperature datasets for the LSMEM forward model approach. This study confirms that remote sensing data have the potential to provide useful hydrologic information, but the accuracy of the geophysical parameters could vary depending on the estimation methods. It cannot be concluded from this study whether the soil moisture estimation by the LSMEM approach will perform better in other geographic, climatic or topographic conditions. Nevertheless, this study sheds light on the effects of different approaches for the estimation of geophysical parameters, which may be useful for current and future satellite missions.     

Outage Performance of Uplink (UL) NOMA Network

Wireless Personal Communications - This paper proposes and analyses the power allocation coefficient normalization for successive interference cancellation in power-domain non-orthogonal multiple...