Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Perspectives on Design and Innovation

A series of studies of top European and other firms has revealed patterns of design management associated with commercial success. Firms that invest resources and professional expertise in product and industrial design in traditional and new industries have been commercially more successful than firms that pay less attention to these aspects of design. As an industry matures there is a shift in emphasis from design associated with technological innovation, to designs supporting technical improvements, and then to supporting user needs, fashion and product variants. These issues are illustrated through the history of the evolution of the bicycle.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

Preliminary studies using hybrid mediated electrochemical oxidation (HMEO) for the removal of persistent organic pollutants (POPs).

This study investigates the hybrid mediated electrochemical oxidation (HMEO) technology, which is a newly developed non thermal electrochemical oxidation process for organic destruction. A combination of ozone and ultrasonication processes to the mediated electrochemical oxidation (MEO) process is termed as hybrid mediated electrochemical oxidation. The electrochemical cell was developed in this laboratory. In the present study, several organic compounds, such as phenol, benzoquinone and ethylenediaminetetraacetic acid (EDTA), were chosen as the model organic pollutants to be destructed by the hybrid process. The organic destruction was monitored based on the CO2 generation and total organic carbon (TOC) reduction. The HMEO process was found to be extremely effective in the destruction of all the target organics chosen in this study. The information obtained from this study will provide an insight in adopting this technique for dealing with more recalcitrant organics (POPs).     

Formation of C4 species in the deactivation of a Pd/SiO2 catalyst during the selective hydrogenation of acetylene

The deactivation characteristics of Pd/SiO₂ in the selective hydrogenation of acetylene were correlated with changes in the amount of the C4 species produced. The amounts of butenes produced changed in parallel with the catalyst activity, indicating that the rate limiting step for butene production was the same as that for acetylene hydrogenation. On the other hand, the amount of 1,3-butadiene produced changed, showing a maximum with catalyst deactivation because 1,3-butadiene is an intermediate in the sequential reaction process which involves both the production and consumption of 1,3-butadiene. This was verified by a simultaneous TG/reaction experiment showing that 1,3-butadiene was a precursor of green oil. The catalyst showed a self-regenerative behavior in its activity and the amounts of C4 species produced during the early stage of deactivation because two opposite factors, which contributed to either the lowering or the promotion of activity, were involved in the process. A specific type of polymer species, produced during the initial period of deactivation, is proposed to be responsible for the promotion of catalyst activity.     

Isothermal interphase diffusion with consecutive reactions

For multi-step heterogeneous consecutive reactions affected entirely by interphase diffusion under isothermal condition, the equations for the effectiveness factors, the surface concentrations and the point yields were derived in terms of the Damkoehler numbers or the measurables from the mass balances set up on the assumption that the mass-transfer rate balances the surface-reaction rate at steady state. From the analyses of the equations derived, the effectiveness factors for the intermediate steps and the surface concentrations of intermediates were understood to be enhanced by the measurables inclusive of the concentrations and the mass-transfer coefficients. Then the effect of the concentrations was concluded to be most significant. The effects of these measurables to the effectiveness factors and the surface concentrations were qualitatively discussed for simple consecutive reactions and also for additive consecutive reactions. Especially, as for two-step additive consecutive reactions, the effects of measurables η Da and the concentrations to the effectiveness factors were examined with graphical presentations. Finally, the brief discussion of the dependency of the Damkoehler number upon reaction time and the effect of the Renolds number and diffusivity to the extent of the mass-transfer resistance were presented.     

Thermal stability of poly(methyl methacrylate)

Summary The average solid-state molecular structures of end-groups generated through chain termination reactions in the polymerization of methyl methacrylate have been derived from published crystallographic data. Evidence is provided for the reduced stability of the head-head chain-termination configuration and in support of the postulate that it is a preferred site of chain scission. Comparable evidence for the unsaturated end group has not been found.     

Ceramers: Hybrid materials incorporating polymeric/oligomeric species with inorganic glasses by a sol-gel process

A sol-gel process has been successfully utilized to produce hybrid materials incorporating polymeric/oligomeric components of polydimethyl siloxane(PDMS) with silicon glasses. All the samples made were transparent and flexible. Dynamic mechanical studies indicate that a portion of the siloxane species is phase-separated while the remainder is well dispersed. The effect of acid content were proven to be significant on the dispersion of the siloxane components and on the structure and properties of final products.     

Classification and prediction of the critical heat flux using fuzzy theory and artificial neural networks

A new method to predict the critical heat flux (CHF) is proposed, based on the fuzzy clustering and artificial neural network. The fuzzy clustering classifies the experimental CHF data into a few data clusters (data groups) according to the data characteristics. After classification of the experimental data, the characteristics of the resulting clusters are discussed with emphasis on the distribution of the experimental conditions and physical mechanism. The CHF data in each group are trained in an artificial neural network to predict the CHF. The artificial neural network adjusts the weight so as to minimize the prediction error within the corresponding cluster. Application of the proposed method to the KAIST CHF data bank shows good prediction capability of the CHF, better than other existing methods.