Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

小剂量辐射对肿瘤细胞K_（562）及肿瘤病人天然杀伤细胞（NK）活性的影响

已知小剂量辐射可增强机体免疫功能。从对高本底地区的调查发现，该地区居民肿瘤死亡率及某些肿瘤发病率有所降低（１）。ＮＫ细胞能直接杀伤肿瘤细胞，在肿瘤免疫中起着重要的作用。本文观察小剂量辐射对肿瘤病人和正常人外周血淋巴细胞ＮＫ活性的相对效应以及对人红白血病细胞（Ｋ（５６２）细胞）的影响，以期从体外买验来探索较小剂量辐射对肿瘤治疗的影响     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

Experience in testing the Motif interface

The testing and quality assurance of the Motif 1.0 graphical user-interface software are described. The testing goals, which fell into three general categories (code coverage, defect-density, and defect-arrival rate), and a deliverable formal test suite are examined. The three phases of the testing process-evaluation, test development, and regression testing-and the tools used in testing are discussed     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

短模型上的明渠非恒定流试验

水工整体模型试验中,明渠非恒定流至今大多被简化为恒定流,而效果有时并不理想。本文指出,只要设置固定式曲线尾门,并有必要的动态量测设备,便可模拟原型非恒定流;即使模型偏短,也能得出比恒定流试验更接近原型的成果。在同一模型上,既做恒定流试验,又进行必要的非恒定流试验,二者相辅相成,必将有助于试验水平的提高。作为例证,本文介绍了泄洪调度导致航道水面波动的一项试验成果,并以岩基冲刷、通航水流条件、围堰过水、河床冲淤等研究课题为例,讨论了采用“短模型非恒定流试验方式”的必要性与可行性。     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。     

Penalty interference of nonlinear intra-channel effects and PMD inultra high-speed TDM systems

Penalty interference of nonlinear propagation impairments and polarisation mode dispersion (PMD) caused signal distortions is experimentally investigated     

Assessment of underground cable ratings based on distributed temperature sensing

Numerous power utilities have installed advanced distributed temperature sensing (DTS) systems to measure the temperature of underground cables. This paper presents a general procedure for real-time assessment of underground cable ratings based on DTS. After the identification and location of hot spots on a cable, the cable installation data, load, and DTS-recorded temperature over a period of time are used to estimate soil thermal parameters and assess cable ratings under normal and overloading conditions. In order to accurately estimate soil thermal parameters, a combined technique of the finite-element method and gradient-based optimization is used. The technique was validated in the laboratory and applied to a rating assessment of a 230-kV/500-MVA cable circuit. The assessed continuous and emergency ratings are helpful in improving the operation of this circuit.