动态评价技术在塔河碳酸盐岩缝洞型油气藏中的应用

塔河油田奥陶系油气藏是大型碳酸盐岩溶洞型油气藏，其储渗空间主要为大小不同的溶洞、裂缝带、溶蚀孔隙等组成，该油气藏具有极强的非均质性，单纯用静态资料来认识这类油气藏是非常困难。文章提出利用生产动态资料和信息进行该类型油气藏研究的新思路，利用人工神经网络技术在处理非线性相关参数预测方面的优势，并以渗流理论为基础，结合试井成果，选用已知油井的产量、油嘴、油压、含水率、气油比、原油密度等6个开发动态参数作为样品输入数据，推导出影响油气藏开发的重要参数（地层系数）与生产信息的关系，建立了人工神经网络预测储层参数的结构模型。通过塔里木盆地塔河油气田实例研究，说明了利用动态信息评价油气藏技术在碳酸盐岩缝洞型油气藏储层预测和非均质性分析等方面具有较高的实用价值。     

Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

Profile-Driven Component Placement for Cluster-Based Online Services

The growth of the Internet and of various intranets has spawned a wealth of online services, most of which are implemented on local-area clusters using remote invocation (for example, remote procedure call/remote method invocation) among manually placed application components. Component placement can be a significant challenge for large-scale services, particularly when application resource needs are workload dependent. Automatic component placement has the potential to maximize overall system throughput. The key idea is to construct (offline) a mapping between input workload and individual-component resource consumption. Such mappings, called component profiles, then support high-performance placement. Preliminary results on an online auction benchmark based on J2EE (Java 2 Platform, Enterprise Edition) suggest that profile-driven tools can identify placements that achieve near-optimal overall throughput.     

电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

Joint scheduling and power control supporting multicasting in wireless ad hoc networks

This paper addresses the problem of power control in a multihop wireless network supporting multicast traffic. We face the problem of forwarding packet traffic to multicast group members while meeting constraints on the signal-to-interference-plus-noise ratio (SINR) at the intended receivers. First, we present a distributed algorithm which, given the set of multicast senders and their corresponding receivers, provides an optimal solution when it exists, which minimizes the total transmit power. When no optimal solution can be found for the given set of multicast senders and receivers, we introduce a distributed, joint scheduling and power control algorithm which eliminates the weak connections and tries to maximize the number of successful multicast transmissions. The algorithm allows the other senders to solve the power control problem and minimize the total transmit power. We show that our distributed algorithm converges to the optimal solution when it exists, and performs close to centralized, heuristic algorithms that have been proposed to address the joint scheduling and power control problem.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003