Selectivity Enhancement to the Exclusive Formation of Ethyltoluenes and Hydrogen During Dehydroalkylation of Toluene with Ethane

The dehydroalkylation of toluene with ethane to the isomeric ethyltoluenes was studied on 0.4Pt/H-ZSM-5 at varying contact times (1/WHSV). At a high contact time of 1.0 h, toluene disproportionation and hydrogenolysis reactions dominate, resulting in low selectivity to the desired ethyltoluenes via the alkylation reaction. However, at a low contact time of 0.12 h side reactions are eliminated, resulting in maximum selectivities to the kinetically favored ethyltoluenes and hydrogen. Results at high selectivities to ethyltoluenes provide significant insight into reaction pathways.     

Photocatalytic degradation of methyl tert‐butyl ether (MTBE) in contaminated water by ZnO nanoparticles

BACKGROUND: Over the past several decades methyl tert‐butyl ether (MTBE) as additive to gasoline, intended to either boost ratings of fuel or to reduce air pollution, has been accepted worldwide. Since MTBE has high water solubility, the occurrence of fuel spills or leaks from underground storage tanks or transferring pipeline has led to the contamination of natural waters. In this study the degradation of aqueous MTBE at relatively high concentrations was investigated by a UV‐visible/ZnO/H₂O₂ photocatalytic process. The effects of important operational parameters such as pH, amount of H₂O₂, catalyst loading and irradiation time were also investigated. Concentration of MTBE and intermediates such as tert‐butyl formate and tert‐butyl alcohol were measured. RESULTS: Time required for complete degradation increased from 20 to 150 min when the initial concentration was increased from 10 to 500 mg L^?1. The first‐order rate constants for degradation of MTBE were estimated to be 0.183–0.022 min^?1 as the concentration increased from 10 to 500 mg L^?1. Study of the overall mineralization monitored by total organic carbon analysis showed that at an initial concentration of 100 mg L^?1 MTBE complete mineralization was obtained after 100 min under UV‐visible/ZnO/H₂O₂ photocatalysis. CONCLUSION: The data presented in this paper clearly indicated that UV‐visible/ZnO/O₂ as an advanced oxidation process provides an efficient treatment alternative for the remediation of MTBE‐contaminated waters. Copyright © 2008 Society of Chemical Industry     

Visual comparability of 3D regular sampling and reconstruction

The Body-Centered Cubic (BCC) and Face-Centered Cubic (FCC) lattices have been analytically shown to be more efficient sampling lattices than the traditional Cartesian Cubic (CC) lattice, but there has been no estimate of their visual comparability. Two perceptual studies (each with N = 12 participants) compared the visual quality of images rendered from BCC and FCC lattices to images rendered from the CC lattice. Images were generated from two signals: the commonly used Marschner-Lobb synthetic function and a computed tomography scan of a fish tail. Observers found that BCC and FCC could produce images of comparable visual quality to CC, using 30-35 percent fewer samples. For the images used in our studies, the L(2) error metric shows high correlation with the judgement of human observers. Using the L(2) metric as a proxy, the results of the experiments appear to extend across a wide range of images and parameter choices.     

Multiple model bank selection based on nonlinearity measure and H-gap metric

This paper provides a systematic method for model bank selection in multi-linear model analysis for nonlinear systems by presenting a new algorithm which incorporates a nonlinearity measure and a modified gap based metric. This algorithm is developed for off-line use, but can be implemented for on-line usage. Initially, the nonlinearity measure analysis based on the higher order statistic (HOS) and the linear cross correlation methods are used for decomposing the total operating space into several regions with linear models. The resulting linear models are then used to construct the primary model bank. In order to avoid unnecessary linear local models in the primary model bank, a gap based metric is introduced and applied in order to merge similar linear local models. In order to illustrate the usefulness of the proposed algorithm, two simulation examples are presented: a pH neutralization plant and a continuous stirred tank reactor (CSTR).     

Experimental investigation of the flow-induced motion of a square-section cylinder

The flow-induced motion(FIM)of an elastically mounted square-section cylinder is experimentally investigated over a wide range of Reynolds numbers(1.5×104＜Re＜7....     

High Gain Modified Dual-Band and Dual-Circularly Polarized Array Antenna

Wireless Personal Communications - A novel design of double-layer dual-band circularly polarized array antennas (DDCPAAs) is presented in this paper. First, a DDCP single antenna is introduced as...     

Knowledge Diffusion of the Internet of Things (IoT): A Main Path Analysis

Wireless Personal Communications - The Internet of Things (IoT) is a concept that has attracted significant attention since the emergence of wireless technology. The knowledge diffusion of IoT...     

Correlation of H2S solubility in aqueous MDEA solutions using electrolyte-modified Peng-Robinson plus association equation of state

In this survey, we use the emPR-CPA equation of state to model a ternary system of H₂S solubility in MDEA aqueous solution at different solution compositions, temperatures, pressures, and acid gas loadings. For electrolyte part of the model, MSA theory and the Born term were used. There were 302 experimental data used in this work. To model a ternary system, at first pure components, then binary subsystems, and finally ternary system were modeled using a reactive bubble point pressure calculation method. An overall absolute average deviation percentage equal to 20.85 was achieved so that show the model efficiency for correlation of such systems.     

Synergistic effect of nanoparticles and Thalassospira sp. isolated from Bahregan area in biodegradation of oil sludge

Oil sludge is obtained from the contaminated site of Bahregan area in the Persian Gulf in Iran. Chemotaxis was used for the isolation of alkane-degrading bacteria from oil sludge and the alk genes were determined with specific primers. bac1 identified in Thalassospira was selected as a powerful strain for biodegradation of oil sludge. Biodegradation of oil sludge by bac1 in the presence of nanoparticles was investigated by GC-MS analysis. Synergistic effect of Fe₂O₃ and Fe₃O₄ nanoparticles on bacteria increases the biodegradation of oil sludge and produces cyclosiloxane compound which is used in the field of medicine; however, the Thalassospira reduced its toxicity in the environment.     

Measurement of the amount and rate of methane dissolution in pure water and aqueous solution of SDS + multi-wall carbon nanotubes + β-cyclodextrin

In this paper, the impact of the mixture of sodium dodecyl sulfate (SDS) + multi-wall carbon nanotubes (MWCNTs) + β-cyclodextrin on the quantity and initial rate of methane dissolved in water is investigated. The experiments were performed at a temperature range of 278.15–303.15 K and an initial pressure of 0.5 MPa. The experimental results show that simultaneous utilization of β-cyclodextrin (0.01 mass fraction), MWCNTs (0.0005 mass fraction), and SDS (0.001 mass fraction) at 278.15 K increases the amount and the rate of methane dissolution in water by 29.90% and 173.78%, respectively, compared to pure water. An increase in the temperature decreases the quantity and the initial rate of methane dissolution in all solutions containing additives. However, no consistent relationship is observed between the temperature and the enhancement percentage of solubility of methane in solutions containing additives.