Fracture load and microcrack comparison of crowns manufactured from tooth‐shaped and traditional blocks

This study intended to analyze microcracks and fractographic markings on the surface of all ceramic crowns after milling and compare the fracture loads. 90 crowns were manufactured from two feldspathic (Priticrown‐Pr and Vita Mark II‐Vi) and a lithium disilicate (EmaxCAD‐Em) blocks (n = 30). Two groups (n = 15) were prepared for each ceramic. In the first group, crowns were analyzed twice via the fluorescent penetrant method for microcrack detection, after the manufacturing process and thermal cycles. The load to fracture test was applied at a crosshead speed of 0.5 mm/min until catastrophic failure. Second group crowns were directly cemented onto the Co‐Cr dies following the manufacturing process and loaded to fracture. Fractographic markings were analyzed through scanning electron microscope. Spearman correlation analysis, Kruskal–Wallis H test, Mann–Whitney U test, and Wilcoxon Signed Rank test were applied (α = .05). Fracture loads of Em crowns were higher than other groups (p < .05), with and without the aging procedure. Except for second group Pr (r = ?.532), no significant relationship was found between microcrack numbers and fracture loads (p > .05). Thermal cycling did not affect microcrack numbers and fracture loads (p > .05). Tooth‐shaped multilayered Pr blocks did not provide an advantage in terms of microcrack and fracture loads.     

Flexible poly(styrene-ethylene-butadiene-styrene) hybrid nanofibers for bioengineering and water filtration applications

Among the thermoplastic elastomers that play important roles in the polymer industry due to their superior properties, styrene-based species and polyurethane block copolymers are of great interest. Poly(styrene-ethylene-butadiene-styrene) (SEBS) as a triblock copolymer seems to have the potential to meet many demands in different applications due to various industrial requirements where durability, biocompatibility, breaking elongation, and interfacial adhesion are important. In this study, the SEBS triblock copolymer was functionalized with natural (Satureja hortensis, SH) and synthetic (nanopowder, TiO₂) agents to obtain composite nanofibers by electrospinning and electrospraying methods for use in biomedical and water filtration applications. The results were compared with thermoplastic polyurethane (TPU) composite nanofibers, which are commonly used in these fields. Here, functionalized SEBS nanofibers exhibited antibacterial effect while at the same time improving cell viability. In addition, because of successful water filtration by using the SEBS composite nanofibers, the material may have a good potential to be used comparably to TPU for the application.     

Efficient manganese decorated cobalt based catalysts for hydrogenation of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) biofuel

2,5-dimethylfuran (DMF) is a promising compound in the production of biofuel with high-quality properties. In this study, it is aimed to develop new efficient catalysts to synthesize DMF from 5-hydroxymethylfurfural (HMF). Co, Mn/Co, and Ru/Co catalysts were prepared using the NaBH₄ reduction method. The catalysts were subjected to activity tests for the hydrogenation of HMF to DMF by changing the reaction parameters, such as temperature and time. Mn/Co catalysts prepared from metal precursors at various molar ratios of Mn/Co were found to be effective in hydrogenation reactions of HMF to DMF. A 91.8% DMF yield was achieved in the presence of a Mn/Co (50/50) catalyst without noble metal at 180°C for 4 hours. The Brunauer-Emmet-Teller (BET) method, x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), and induction coupled plasma mass spectroscopy (ICP-MS) techniques were used to characterize the efficient Mn/Co catalyst.     

Efficacy of multi-mode adhesive systems on dentin wettability and microtensile bond strength of resin composite

Purpose: To evaluate the wetting ability and the microtensile bond strength of adhesive systems in various depths of dentin. Materials and Method: 48 extracted human molars cut in half in buccolingual direction. Buccal and lingual surfaces were used to obtain deep (n = 48) and superficial (n = 48) dentin. Groups were divided into 4 subgroups: Self-etch (CSE), etch&rinse (SB), multi-mode self-etch (SAU) and multimode etch&rinse (EAU) adhesive systems. 3 consecutive contact-angle measurements were obtained: T0- 3 μl drop of distilled water on dentin; T1-Droplet of the adhesive; T2- Distilled water after polymerization of the adhesive. After composite build-ups, microtensile measurements were performed. Contact angle data were analysed with analysis of variance for repeated measures. Bond strength data were analyzed by repeated measures analysis of variance, comparisons were made according to the logarithmic values (p < 0.05). Results: The difference between groups was not significant regardless of dentin depth for all measurements (p < 0.05). All groups except CSE enhanced the wetting ability of the adhesive but reduced the wetting ability of distilled water after application of the adhesive (p < 0.05). Regarding adhesive systems, the groups showed no significant difference between bond strengths to various depths of dentin except SAU (p > 0.05); in SAU, bond strength to deep dentine were significantly higher than superficial dentin (p < 0.05). Regarding adhesives’ bond strength, CSE showed significantly greater values than the other groups (p < 0.05). Conclusion: The cavity depth does not affect the bonding ability for all adhesive systems; self-etch adhesive systems might be a better choice since different adhesives may influence the wetting ability and microtensile bond strength of the dentin substrates.     

Quinoxaline derivatives as long wavelength photosensitizers in photoinitiated cationic polymerization of diaryliodonium salts

The present paper is focused on visible light initiated cationic polymerizations. Photoinitiated polymerization of representative vinyl ether and oxirane monomers using two quinoxaline derivatives; namely (2-(2,3-dihydrobenzo [b][1,4]dioxin-6-yl)-3-(2,3-dihydrobenzo[b]-[1,4]dioxin-7-yl)-5-(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-8-(2,3-dihydrothieno[3,4-b][1,4]dioxin-7yl) quinoxaline) (DBQEd) and 2,3,5,8-tetra(thiophen-2-yl)quinoxaline (TTQ) are studied. Novel dyes based on the quinoxaline skeleton are employed as efficient photosensitizers in cationic photopolymerizations. Polymerizations were initiated at room temperature upon irradiation with long-wavelength UV and visible lights in the presence of diphenyliodonium hexafluorophosphate (Ph₂I⁺PF₆^?). The progress of the polymerizations was monitored by optical pyrometry (OP). Solar irradiation is also employed to carry out the cationic polymerization of a diepoxide monomer in the presence of air.     

Determination of mechanical properties of polymeric microspheres used in controlled drug delivery systems by nanoindentation

In this study, we synthesized poly (vinyl acetate-co-divinyl benzene) microspheres with various monomer/cross-linker contents for oral/topical sustained drug release applications and determined the micromechanical properties by nanoindentation. Compression elastic moduli of materials were calculated by using the limited depth of indentation according to Hertz elastic deformation model and presented as the histogram of multiple data. In terms of drug release practices, poly (VAc-co-DVB) microspheres with a high DVB content, especially in topical applications, are expected to carry drugs under mechanical stresses of less than 1.0 GPa.     

Influence of pH on recombinant human growth hormone production by Pichia pastoris

BACKGROUND: Effect of pH on recombinant human growth hormone (rhGH) production by Pichia pastoris hGH‐Mut⁺ was investigated at pH = 4.2, 5.0, 5.5, and 6.0. RESULTS: The highest cell concentration was obtained at pH = 6.0 with 53 g L^?1, while the highest rhGH concentration was attained at pH = 5.0 as 0.27 g L^?1. Total protease secretion increased with increase in pH and with the cultivation time. Oxygen uptake rate increased with increasing pH up to pH = 6.0, having the maximum value, 37 mmol m^?3 s^?1, at pH = 5.5. K_La values were similar at all the conditions, having a maximum value of 0.14 s^?1 at pH = 5.0. Taking the final rhGH concentration into account, the most favourable pH was 5.0; where AOX1 expression level showed a similar trend to AOX activity profiles, having the highest value of 9.4 × 10¹⁰ copy mg^?1 CDW at t = 15 h; in parallel to AOX1 expression profile, hGH expression level increased until t = 15 h, with the highest value of 4.0 × 10¹⁰ copy mg^?1 CDW, where a sharp increase in rhGH concentration was obtained. The expression levels of pep4, prb1 and prc1 genes, responsible from the production of proteinase A, proteinase B and, carboxypeptidase Y, were parallel to each other. CONCLUSION: Since it was shown that pH is a crucial operating parameter in fermentation processes using P. pastoris, keeping pH constant at its determined optimum value, pH = 5.0, during the bioprocess is vital in terms of recombinant protein production. Copyright © 2010 Society of Chemical Industry