Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Identification and analysis of genes from Streptomyces pristinaespiralis encoding enzymes involved in the biosynthesis of the 4-dimethylamino-L-phenylalanine precursor of pristinamycin I

Dextran has been used as a carrier molecule for the synthesis of monofunctional peptide-dextran conjugates. The immunodetection of such carrier immobilized peptides on ELISA plates was compared to that of peptides adsorbed directly to immunoplates. The main features observed with peptide-dextran conjugates were as follows: only small amounts of peptide (1-2 mg) were necessary for coupling via alpha- or epsilon-amino groups to NaIO4-activated dextran (4 mg); the coupling yield was up to 68%; an amino acid analysis of the conjugate enabled the amount of carrier immobilized peptide to be calculated; an estimated 15-17 peptides were bound per dextran molecule (MW 73,500); using a carbohydrate as carrier reduces the possibility of non-specific interactions because no hydrophobic or ionic sites and no protein-like epitopes exist on the carrier apart from the peptide ligand. It can be assumed that some peptide ligands provide the forces for an interaction with the plate surface whereas other remain free for the interaction with the antibody. Thus, the detection with monoclonal anti-peptide antibodies allowed peptide-dextran conjugates to be used at coating concentrations of 1-3 nM peptide, corresponding to 0.6-2.6 ng peptide-dextran per well. In contrast, concentrations of 150-500 nM were required for coating with peptides. The applicability of monofunctional peptide-dextran conjugates was demonstrated by investigating the titer and specificity of a polyclonal anti-peptide serum developed against human gastrointestinal glutathione peroxidase. The introduction of biotin as a second ligand of the dextran conjugate permitted its capture on streptavidin coated plates. This synthesis of bifunctional peptide-biotin-dextran conjugates opens up additional possibilities for applications.     

High-speed tandem of MQW modulators for coded pulse generation with 14-dB fiber-to-fiber gain

We report on a tandem of electroabsorption modulators integrated with an amplifier by the identical active layer (IAL) approach. A 14 dB fiber-to-fiber is obtained by the use of constant As-P ratio MQW active layer and operation at 10 Gb/s is demonstrated. A record modulator saturation power of 35 mW is also reported.     

Color quantitation through image processing in dermatology

Classical color models and their applications to computer vision are reviewed. The performances of color quantitation from digitized images are compared with those derived from a chromameter. The color quantitation obtained from either digitized color slides or directly digitized images is proved to be more efficient than the conventional visual assessment of observers. A methodology is proposed for determining the specific color indices which are needed in dermatology. An application of this methodology is developed for designing a blanching quantitation index in order to replace the visual assessment during McKenzie tests.     

Choquet optimal set in biobjective combinatorial optimization

We study in this paper the generation of the Choquet optimal solutions of biobjective combinatorial optimization problems. Choquet optimal solutions are solutions that optimize a Choquet integral. The Choquet integral is used as an aggregation function, presenting different parameters, and allowing to take into account the interactions between the objectives. We develop a new property that characterizes the Choquet optimal solutions. From this property, a general method to easily generate these solutions in the case of two objectives is defined. We apply the method to two classical biobjective optimization combinatorial optimization problems: the biobjective knapsack problem and the biobjective minimum spanning tree problem. We show that Choquet optimal solutions that are not weighted sum optimal solutions represent only a small proportion of the Choquet optimal solutions and are located in a specific area of the objective space, but are much harder to compute than weighted sum optimal solutions.     

Characterization of the thermal properties of PLA fibers by modulated differential scanning calorimetry

Polylactide (PLA) has been melt spun to produce multifilament continuous yarns. The thermal characteristics of PLA filaments have been investigated using modulated differential scanning calorimetry (MDSC). With MDSC, it is possible to separate the different thermal events and to analyze them more precisely. The influence of hot drawing on thermal properties of PLA filaments has been studied. Hot drawing promotes an increase of glass transition temperature (T_g) and a decrease of heat capacity. The cold crystallization spreads on a larger range of temperature and the peak occurs at a lower temperature. The initial degrees of cristallinity of PLA filaments have been calculated thanks to the reversing and non reversing curves of MDSC. Tensile properties of PLA filaments are also investigated.     

Assorted analytical and spectroscopic techniques for the optimization of the defect-related properties in size-controlled ZnO nanowires

In this article, the important role of the intrinsic defects in size-controlled ZnO nanowires (NWs) which play a critical role in the properties of the NWs, was studied with a combined innovative experimental analysis. The NWs prepared by both the aqueous solution method and chemical vapour deposition process were of increasing length and decreasing size-to-volume (S/V) ratio. The combined approach involved different analytical and spectroscopic techniques and from the correlation between the different measurements, the concentration of the oxygen vacancies jointly with the zinc interstitials defects and the zinc vacancy defects was observed to be positively or negatively correlated, respectively, with the magnitude of the photoluminescence intensity and radiative lifetimes. Furthermore, the experimental results also suggest that the oxygen vacancy defects are not only spatially located on the surface of the NW but an increasing fraction of the total oxygen vacancy defects connected with the green emission is also located in an annulus region beneath the surface as the ZnO NWs elongate. On the other hand, as the donor concentration plays a critical function in the properties of the ZnO NWs, an analytical model was derived for the calculation of the donor concentration of the NWs directly from its reverse-biased current-voltage characteristics obtained from the conductive atomic force microscopy measurements.     

Comparison of the wound-activated transformation of caulerpenyne by invasive and noninvasive Caulerpa species of the Mediterranean

The invasive green alga, Caulerpa taxifolia, that has spread rapidly after its introduction into the Mediterranean and the North American Pacific, reacts to wounding by transforming its major metabolite caulerpenyne (1). This wound-activated reaction involves the transformation of the bis-enol acetate moiety of 1, releasing reactive 1,4-dialdehydes. The ability to perform this transformation is found also in both the noninvasive Mediterranean C. prolifera and the invasive C. racemosa. Trapping experiments, as well as transformation of the model substrate geranyl acetate, suggest that all three investigated Caulerpa spp. rely on esterases that act upon wounding of the algae by subsequently removing the three acetate residues of caulerpenyne. The resulting reactive 1,4-dialdehyde oxytoxin 2 (9) can be identified by liquid chromatography–mass spectrometry and is unstable in the wounded tissue. Caulerpenyne transformation occurs rapidly, and severe tissue damage caused degradation of more than 50% of the stored caulerpenyne within 1 min in all three algae. Prevention of the enzymatic reaction before extraction, by shock freezing the tissue with liquid nitrogen, was used for the determination of the caulerpenyne content in intact algae. It gives about twofold higher values compared to an established methanol extraction protocol. The speed and mechanism of the wound-activated transformation, as well as the caulerpenyne content in intact tissue of invasive and noninvasive Caulerpa spp., are comparable. Thus, this enzymatic , transformation, despite being fast and efficient, is likely not the key for the success of the investigated invasive species.     

Oxidation Kinetics of Carbon Deposited on Cerium‐Doped FePO4 during Dehydration of Glycerol to Acrolein

A cerium‐doped FePO₄ catalyst dehydrates glycerol to acrolein in the gas phase but carbon accumulation reduces the reaction rate with time. Reaction rates may be maintained for longer times by co‐feeding low concentrations of oxygen together with the glycerol, but the acrolein yield drops proportionally to the oxygen concentration. The catalyst is easily regenerated by air and the reaction rate is proportional to both the oxygen concentration and quantity of carbon. The carbonaceous deposits may be due to both glycerol and acrolein: when either is fed to the catalyst, the CO₂/CO ratio is close to 1; during the regeneration step, the CO₂/CO ratio is near 4. A kinetic model of first order in both oxygen concentration and adsorbed sites characterizes the transient data very well.     

Part 1. Qualitative comparison between polymer and monomer model compound sulfonation

The sulfonation kinetics of fluorine ended poly(ether ether ketone) (PEEK) in solution in 95.9% and 96.8% concentrated sulfuric acid was studied with the help of a model compound representative of the PEEK chain repeat unit. The reaction rate of the model compound sulfonation was found to be first order with respect to the aromatic ring to be sulfonated. Consequently, PEEK kinetic data were treated following a first order with respect to the unsulfonated repeat unit concentration. Two rate‐slowing effects were detected. They were attributed to ‘long range’ electronic effects resulting from the inductive nature of the fluorine atom, and from the electron‐withdrawing character of the grafted sulfonic acid group. © 2001 Society of Chemical Industry