A 1.5-V full-swing BiCMOS logic circuit

A BiCMOS logic circuit applicable to sub-2-V digital circuits has been developed. A transiently saturated full-swing BiCMOS (TS-FS-BiCMOS) logic circuit operates twice as fast as CMOS at 1.5-V supply. A newly developed transient-saturation technique, with which bipolar transistors saturate only during switching periods, is the key to sub-2-V operation because a high-speed full-swing operation is achieved to remove the voltage loss due to the base-emitter turn-on voltage. Both small load dependence and small fan-in dependence of gate delay time are attained with this technique. A two-input gate fabricated with 0.3-μm BiCMOS technology verifies the performance advantage of TS-FS-BiCMOS over other BiCMOS circuits and CMOS at sub 2-V supply     

Hydroliquefaction of low-sulfur coals using iron carbonyl complexes—Sulfur as catalysts

Hydroliquefaction of low-sulfur Australian coals (Wandoan and Yallourn) was studied using iron carbonyl complexes as catalyst. The addition of Fe(CO)₅ (2.8 wt% Fe of coal) increased coal conversion from 48.6 to 85.2% for Wandoan coal, and from 36.7 to 69.7% for Yallourn coal in 1-methylnaphthalene at 425°C under an initial hydrogen pressure of 50 kg cm^?2. When molecular sulfur was added to iron carbonyls (Fe(CO)₅, Fe₂(CO)₉ and Fe₃(CO)₁₂), higher coal converions ( > 92%) and higher oil yields (>46%) were obtained, along with an increase in the amount of hydrogen transferred to coal from the gas phase (0.2 to 2.8%, d.a.f. coal basis). In the liquefaction studies using a hydrogen donor solvent, tetralin, Fe(CO)₅S catalyst increased the amount of hydrogen absorbed from the gaseous phase and decreased the amount of naphthalene dehydrogenated from tetralin. The direct hydrogen transfer reaction from molecular hydrogen to coal fragment radicals seems to be a major reaction pathway. Organic sulfur compounds, dimethyldisulfide and benzothiophene, and inorganic FeS₂ and NiS were found to be good sulfur sources to Fe(CO)₅. From X-ray diffraction analyses of liquefaction residues, it is concluded that Fe(CO)₅ was converted into pyrrhotite (Fe_1?xS) when sulfur was present, but into Fe₃O₄ in the absence of sulfur.     

Development of a dual‐lamp projector with higher brightness

Stationary projectors mainly used in system applications have recently gained a wider application range, including general presentations in halls and large conference rooms and being used, for example, in digital signage and for monitoring purposes. Consequently, they are required to meet new market demands for durability, reliability, and flexibility in installation in addition to their conventional basic performance such as especially high brightness. To achieve especially high brightness, a new optical system with two lamps is proposed; the profile of the cover glass that prevents the glass from scattering is made aspherical, the profile of the beam‐combining mirror is improved with its position optimized, and the size of the incident plane of the integrator rod is made larger (1.1 times). These measures resulted in an optical system of an even higher efficiency with 7000 lm, which is the highest in its class (according to a June 2010 investigation). Also, the arrangement of two parallel lamps completely eliminated the effect of heat passing from one lamp to the other, which helped secure durability, reliability, and flexibility in installation. Furthermore, the combined use of the unique non‐telecentric optical system, adopted from the conventional single‐lamp model, helps maintain the class‐highest contrast ratio.^1,2     

Estimation procedure for the Weibull parameters used in the local approach

The local approach was recently proposed by Beremin and Mudry for evaluating the statistical behaviour of toughness results of materials. This approach introduces a stress parameter _w , termed the Weibull stress, as a measure of the fracture resistance of materials instead of the conventional toughness parameters such as K _c, _c and J _cl (critical stress intensity factor, CTOD and J-integral, respectively). The Weibull stress _w obeys the Weibull distribution with the two parameters m and _u (the shape and the scale parameter, respectively). The first parameter m is normally estimated to be 22 irrespective of the kind of material. In this paper a procedure for the determination of the Weibull parameters m and _u is developed. This procedure consists of the determination of the plastic zone ahead of the crack tip, from which cleavage fracture originates, and of the maximum likelihood estimation of the parameters m and _u based on the stress distribution in the plastic zone. Calculations using this procedure confirm that the distribution of the Weibull stress _w is a material property independent of specimen thickness, and in particular that the shape parameter m depends on the material, e.g. m12 for a German reactor pressure vessel steel (20 Mn Mo Ni 5 5). Using these parameters for the distribution of the Weibull stress the size effect in fracture toughness values is predicted and an improved agreement between theory and experiments is obtained compared to the Weakest Link model.     

A PRACTICAL METHOD FOR RECTIFYING INTERFACIAL TENSION DATA TO PREDICT THE SHAPE OF INTERFACES IN AN IMMISCIBLE LIQUID/LIQUID/GAS SYSTEM

The shape of interfaces formed by the contact of two liquid phases, immiscible with each other, and a gaseous phase can be predicted on the condition that the tension to work at each interface is known with a sufficient accuracy. In general, interfacial tension data available are not so accurate, however, as to be useful as they are in predicting the shape of interfaces, particularly when the spreading coefficient of either liquid (liquid 1) on the other (liquid 2) has a negative value of a small magnitude. Presented in this note is a simple method to rectify the interfacial tension data, with the aid of a measurement of the radius of a lens of liquid 1 of a known volume placed on the horizontal surface of liquid 2, and thereby make them usable for predicting interfacial geometries. The method is tested by applying it to benzene/water and n-pentane/water systems.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Nitrous oxide emissions from fertilized upland fields in Thailand

Nitrous oxide (N₂O) emission from fertilized maize fields was measured using a closed chamber at four experimental sites in Thailand. The average measured N₂O flux from unfertilized plots through crop season was 4.16 ± 1.52, 5.05 ± 1.65, 5.25 ± 1.68 and 6.74 ± 2.95 g N₂O-N m^-2 h^-1, at Nakhon Sawan, Phra Phutthabat, Khon Kaen and Chiang Mai, respectively. Increased N₂O emissions by the application of nitrogen fertilizer were 0.22–0.44, 0.19–0.38%, 0.12–0.24 and 0.08–0.15% of the applied N, respectively. Compared to other data, N₂O emission rate to applied nitrogen was not significantly different between the data of Thailand and the Temperate Zone.     

High aspect ratio fabrication method using O2 RIE and electroplating

A polyimide-based process for the fabrication of vertical structures with high aspect ratio has been developed. O₂ reactive ion etching (O₂ RIE) has been employed in the polyimide processing. Achieved etching characteristics of the O₂ RIE system are: 4.0 m/min etching rate, 15 aspect ratio, 75 m etching depth. Polyimide has excellent chemical and thermal properties which makes it a good building material for micromachines. Polyimide could be also used as molds for electroplating. Electroplated copper structures were formed in the polyimide molds and metal gears were fabricated by these fabrication technologies. New possibilities for micromachining were opened by the use of O₂ RIE and electroplating.This work was supported by Japanese ministry of Education Science and Culture under a grant-in-Aid No. 03102001.     

Proposal of variable sequential sampling plan having desired operating characteristics indexed by quality loss

The proportion of non-conforming items has been traditionally utilised as an evaluation criterion for quality of items. However, the proportion of non-conforming items is not necessarily useful as a proper evaluation criterion for controlling high-quality manufacturing in recent years. Accordingly, in order to achieve further quality improvement and innovation, more careful quality evaluation has been required newly. Then, a concept of quality loss in the Taguchi methods has been devised as a severe criterion of quality evaluation. Hereby, a variable single sampling plan having desired operating characteristics (OCs) indexed by quality loss has been proposed in the area of statistical quality control. By the way, the most economical sampling inspection in the average sample number (ASN) is the sequential sampling plan based on the Wald’s sequential probability ratio test. Then, from the viewpoint of cost reduction, we discuss a variable sequential sampling plan having desired OC indexed by quality loss with the aim of expansion of the utility of variable sampling plan for quality loss. As the result, the design procedure of the sequential sampling plan for satisfying some required design conditions indexed by quality loss is provided. In addition, the effectiveness of the proposed sequential sampling plan is verified through some numerical examples.