Strain hardening due to deformation twinning in α-titanium: Mechanisms

Novel experiments were conducted to elucidate the effect of deformation twinning on the mechanical response of high-purity α-titanium deformed at room temperature. Orientation-imaging microscopy (OIM), microhardness, and nanohardness evaluations were employed in conjunction with optical microscopy and quasi-static compression testing to obtain insight into the deformation mechanisms. Hardness measurements revealed that the newly formed deformation twins were harder than the matrix. This observation is perhaps the first experimental evidence for the Basinski mechanism for hardening associated with twinning, arising from the transition of glissile dislocations to a sessile configuration upon the lattice reorientation by twinning shear. This work also provided direct evidence for two competing effects of deformation twinning on the overall stress-strain response: (1) hardening via both a reduction of the effective slip length (Hall-Petch effect) and an increase in the hardness of twinned regions (Basinski mechanism) and (2) softening due to the lattice reorientation of the twinned regions.     

On the credibility of manet simulations

Simulation is useful for evaluating protocol performance and operation. However, the lack of rigor with which it's applied threatens the credibility of the published research within the manet research community. Mobile ad hoc networks (manets) allow rapid deployment because they don't depend on a fixed infrastructure. Manet nodes can participate as the source, the destination, or an intermediate router. This flexibility is attractive for military applications, disaster-response situations, and academic environments where fixed net working infrastructures might not be available.     

On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.