Tribromopyrrole,brominated acids,and other disinfection byproducts produced by disinfection of drinking water rich in bromide

Using gas chromatography/mass spectrometry (GC/MS), we investigated the formation of disinfection byproducts (DBPs) from high bromide waters (2 mg/L) treated with chlorine or chlorine dioxide used in combination with chlorine and chloramines. This study represents the first comprehensive investigation of DBPs formed by chlorine dioxide under high bromide conditions. Drinking water from full-scale treatment plants in Israel was studied, along with source water (Sea of Galilee) treated under carefully controlled laboratory conditions. Select DBPs (trihalomethanes, haloacetic acids, aldehydes, chlorite, chlorate, and bromate) were quantified. Many of the DBPs identified have not been previously reported, and several of the identifications were confirmed through the analysis of authentic standards. Elevated bromide levels in the source water caused a significant shift in speciation to bromine-containing DBPs; bromoform and dibromoacetic acid were the dominant DBPs observed, with very few chlorine-containing compounds found. Iodo-trihalomethanes were also identified, as well as a number of new brominated carboxylic acids and 2,3,5-tribromopyrrole, which represents the first time a halogenated pyrrole has been reported as a DBP. Most of the bromine-containing DBPs were formed during pre-chlorination at the initial reservoir, and were not formed by chlorine dioxide itself. An exception wasthe iodo-THMs, which appeared to be formed by a combination of chlorine dioxide with chloramines or chlorine (either added deliberately or as an impurity in the chlorine dioxide). A separate laboratory study was also conducted to quantitatively determine the contribution of fulvic acids and humic acids (from isolated natural organic matter in the Sea of Galilee) as precursor material to several of the DBPs identified. Results showed that fulvic acid plays a greater role in the formation of THMs, haloacetic acids, and aldehydes, but 2,3,5-tribromopyrrole was produced primarily from humic acid. Because this was the first time a halopyrrole has been identified as a DBP, 2,3,5-tribromopyrrole was tested for mammalian cell cytotoxicity and genotoxicity. In comparison to other DBPs, 2,3,5-tribromopyrrole was 8x, 4.5x, and 16x more cytotoxic than dibromoacetic acid, 3-chloro-4-(dichloromethyl)-5-hydroxy-2-[5H]-furanone [MX], and potassium bromate, respectively. 2,3,5-Tribromopyrrole also induced acute genomic damage, with a genotoxic potency (299 microM) similar to that of MX.     

Plastic deformation of dense nanocrystalline yttrium oxide at elevated temperatures

Nanocrystalline yttrium oxide, Y₂O₃ with 110 nm average grain size was plastically deformed between 800 °C and 1100 °C by compression at different strain rates and by creep at different stresses. The onset temperature for plasticity was at 1000 °C. Yield stress was strongly temperature dependent and the strain hardening disappeared at 1100 °C. The polyhedral and equiaxed grain morphology were preserved in the deformed specimens. The experimentally measured and theoretically calculated stress exponent n = 2 was consistent with the plastic deformation by grain boundary sliding. Decrease in the grain size was consistent with decrease in the brittle to ductile transition temperature.     

Experimental Study on Electrostatically Enhanced Granular Filters

Filtration of charged aerosols by granular bed filters enhanced by an externally applied electrostatic field was studied experimentally. The filtration efficiencies of latex aerosols by sand beds were measured for various aerosol and bed granule diameters. The results were compared with theoretical solutions. It was demonstrated that high filtration efficiencies of charged aerosols may be achieved when moderate electrostatic fields are applied to a filter.     

Interfacial chemistry on carboxylate-functionalized monolayer assemblies

Deposition of trichlorosilanes with ester groups at their remote termini provides a convenient entry to carboxylic acid-bearing siloxane-anchored self-assembled monolayers. The de-esterification of these esters has been optimized to minimize monolayer damage, and their quantitative re-esterification provides clear evidence for the stability of these systems. Both the structure of the ester-terminated monolayer and its de-esterification/esterification chemistry can be easily monitored by FTIR-ATR measurements. This spectroscopic tool, together with a liquid cell that enables IR spectra to be measured in an aqueous environment, enables a detailed structural analysis of the carboxylic acid-bearing siloxane-anchored self-assembled monolayers and an assessment of their acid/base behavior (by in situ titration). The use of D₂O instead of H₂O for the in situ titration experiments also improves the available IR window. Both monomeric and dimeric/oligomeric acid groups are seen, and the relative ease of deprotonation of these various species can be directly monitored. Monomers of alkyl carboxylic acids that are hydrogen bonded only to surrounding water molecules have a pK_a = 4.9, while the pK_a for the aggregated molecules is 9.3. Similar behavior is seen for surface-bound benzoic acids, where the two pK_a values are 4.7 and 9.0. The influence of temperature on these structures and their chemistry has been explored to a limited extent as well. When the alkylcarboxylic acid system is cooled to 10 °C, the pK_a value for the acid monomers is reduced from 4.9 to 4.5 and increases from 9.3 to 10.3 for the aggregates.     

Densification of nanocrystalline Y2O3 ceramic powder by spark plasma sintering

Nanocrystalline Y₂O₃ powders with 18 nm crystallite size were sintered using spark plasma sintering (SPS) at different conditions between 1100 and 1600 °C. Dense specimens were fabricated at 100 MPa and 1400 °C for 5 min duration. A maximum in density was observed at 1400 °C. The grain size continuously increased with the SPS temperature into the micrometer size range. The maximum in density arises from competition between densification and grain growth. Retarded densification above 1400 °C is associated with enhanced grain growth that resulted in residual pores within the grains. Analysis of the grain growth kinetics resulted in activation energy of 150 kJ mol^?1 and associated diffusion coefficients higher by 10³ than expected for Y³⁺ grain boundary diffusion. The enhanced diffusion may be explained by combined surface diffusion and particle coarsening during the heating up with grain boundary diffusion at the SPS temperature.     

The Effect of External Electrostatic Field Orientation on Aerosol Filtration by Granular Filters

The separation of fine aerosol particles by a packed granular-bed filter, enhanced by external electrostatic fields, was studied experimentally and theoretically. The filtration efficiencies of charged and neutralized aerosols were measured for external fields aligned with the air flow, transverse to the flow, and opposite to the flow. Theoretical models of electrostatically enhanced granular-bed filtration of micrometer and submicrometer particles were developed. Experimental results which demonstrate the relative merit of each configuration were presented and compared with the theory. The parallel-field configuration yielded the best filtration efficiency followed by the transverse configuration.     

Electrochemical Chromium(III) Oxide Coatings on Non-oxide Ceramic Substrates

SiC and TiB₂ were electrochemically coated with Cr₂O₃ from a 0.1 M aqueous solution of chromium nitrate hydrate with ethanol additives. On both substrate materials poly-crystalline Cr₂O₃ was formed at current densities from 5 to 50 mA/cm² and deposition durations of 5 to 30 min. The coating weight increased with current density and with deposition time. The as-deposited coatings contained microcracks due to drying shrinkage. Microstructural observations indicate that sintering of the Cr₂O₃ coatings on TiB₂ at 1100°C for 1 n in a reducing atmosphere in a closed graphite crucible causes the densification of the coating via a liquid phase, which forms by oxidation of TiB₂. Under similar conditions, the Cr₂O₃ coatings on SiC may be sintered via an evaporation–condensation mechanism.     

Matching with don't-cares and a small number of mismatches

In matching with don't-cares and k mismatches we are given a pattern of length m and a text of length n, both of which may contain don't-cares (a symbol that matches all symbols), and the goal is to find all locations in the text that match the pattern with at most k mismatches, where k is a parameter. We present new algorithms that solve this problem using a combination of convolutions and a dynamic programming procedure. We give randomized and deterministic solutions that run in time O(nk²logm) and O(nk³logm), respectively, and are faster than the most efficient extant methods for small values of k. Our deterministic algorithm is the first to obtain an O(polylog(k)⋅nlogm) running time.     

On the Microstructures Resulting from the Diffusionless Cubic→Tetragonal Transformation in ZrO2-Y2O3 Alloys

A diffusionless cubic (c)→metastable tetragonal (t') phase transformation occurs in certain alloys in the ZrO₂-Y₂O₃ system on quenching from elevated temperatures. Microstructural features due to this phase transformation, principally anti-phase domain boundaries (APB's) and mechanical accommodation twins, have been characterized using transmission electron microscopy. Certain differences between our interpretation and those of other workers are discussed.     

Technological coupling, job characteristics and operators' well-being as moderated by desirability of control

This study proposes that the nature of Automated Manufacturing Technology (AMT)-as reflected in the degree of 'technological coupling' and as perceived by shop floor operators in terms of new job control characteristics (timing and method control, monitoring and problem solving demand, production responsibility)-affects operators' psychological well-being (satisfaction and mental health). The study sample consisted of 216 operators of AMT equipment. Findings indicate that technological coupling is negatively related to the job characteristics of timing and method control, and to psychological well-being variables. Operators' satisfaction is positively related to problem solving, production responsibility and timing and method control. Mental health is negatively related to production responsibility. Implications for job redesign and employees selection to AMT work units are discussed. Yet, results indicate that operators' response to technological coupling is contingent upon their desirability of control (DC). For operators with low DC (as opposed to high DC) coupling conditions did not make any difference in psychological well-being.