Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

C-t analysis of MOS capacitors under constant current stress

The effect of high oxide field stress is studied using capacitance-time (C-t) measurements of MOS capacitors. The stress results in parallel shifts of the C-t curve along the time axis. The flatband voltage shift ΔV_FB obtained from the initial deep depletion capacitance C(t=0⁺) follows the same trend as that from the high-frequency C-V characteristics. However, the discrepancy between the two flatband voltages becomes larger as the stress increases due to the effect of interface charges on C-t characteristics. The flatband voltage difference is converted to interface trap density, showing a steady increase of interface trap density with stress, similar to that from low-frequency C-V measurements     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.     

Presupposition failure — A comedy of errors

Presuppositions of utterances are the pieces of information you convey with an utterance no matter whether your utterance is true or not. We first study presupposition in a very simple framework of updating propositional information, with examples of how presuppositions of complex propositional updates can be calculated. Next we move on to presuppositions and quantification, in the context of a dynamic version of predicate logic, suitably modified to allow for presupposition failure. In both the propositional and the quantificational case, presupposition failure can be viewed as error abortion of procedures. Thus, a dynamic assertion logic which describes the preconditions for error abortion is the suitable tool for analysing presupposition.