Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Preferential Oxidation of CO in H2-Rich Gas at Low Temperatures over Au Nanoparticles Supported on Metal Oxides

We investigated Au catalysts supported on TiO₂, Fe₂O₃, and ZnO for their preferential oxidation of CO in a H₂-rich atmosphere. Both full conversion and selectivity were achieved over Au/Fe₂O₃ and Au/ZnO around room temperature, but at higher temperatures the CO conversion was suppressed due to competition between CO and H₂.     

Photoresponsive peptide and polypeptide systems: part II. Photochromism of poly(l-ornithine) containing various azo-contents in side chains

Poly(L-ornithine)s having various azo-contents in the side chains were synthesized by the water-soluble carbodiimide procedure. The photochemical properties of the polypeptides poly[N^δ-p-(phenylazo)benzoyl-L-ornithine] (PPABLO) containing 3–77 mol% azobenzene were investigated by absorption and circular dichroism spectroscopy in hexafluoro-2-propanol (HFIP) or water, and in HFIP-water or methanol-water solvent mixtures. The photochromism of the dichroic bands of the PPABLOs containing 20–77 mol% azobenzene in the visible and ultraviolet wavelength regions was found to be mostly reversible as a function of irradiation time at different wavelengths due to the photostationary state (above 80% trans-cis photoisomerization) of the azo aromatic moieties. The PPABLO containing 3.2 mol% azobenzene in water exhibited conformational changes from random coil to helix by the addition of methanol or sodium dodecyl sulphate (SDS). The photo-induced conformational change was observed in HFIP-water-SDS solvent mixtures, while no conformational change was seen in water and HFIP-water solvent mixtures.     

The effects of R-75,317 on antiglomerular basement membrane glomerulonephritis in rats

Platelet-activating factor (PAF) is a potent inflammatory mediator which is released by various inflammatory cells and produced by certain tissues, including the kidney. PAF has been shown to increase glomerular permeability to protein and to decrease glomerular filtration rate (GFR) by contracting mesangium. On the basis of these observations, it has been suspected that PAF may play a role as mediator of glomerular damage in glomerular nephritis. To examine this possibility, we studied the effects of a specific PAF antagonist, R-75,317, on the development of an experimental model of anti-glomerular basement membrane (anti-GBM) glomerulonephritis. Glomerulonephritis was initiated by injecting rabbit anti-rat GBM serum into rats. Proteinuria gradually developed after serum injection, plateaued at week 2, and remained at the high level of week 2 throughout the experimental period (6 wk). Chronic treatment with R-75,317 (10 mg/kg/day i.p.) tended to delay the onset of proteinuria and significantly accelerated the recovery phase. Creatinine clearance (Ccr) fell to 40% at week 3. R-75,317 treatment completely prevented this decline of Ccr. Histological changes in this model (glomerular hypertrophy, proliferation of mesangial matrix and interstitial fibrosis) were also ameliorated by the R-75,317 treatment. The results suggest that PAF may play a role in the development of glomerulonephritis and that PAF antagonists could be used in the treatment of human renal disease. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, May 1989.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Drain structure optimization for highly reliable deep submicrometern-channel MOSFET

A guideline for n^- fully gate overlapped (FOLD) structure design optimization has been studied. From the viewpoint of reliability, the greatest reduction in substrate current directly leads to the most reliable n^- design for the FOLD structure. The current path modulation phenomenon due to the trapped charge at the n ^- extension region dominates the hot-carrier induced characteristics change for conventional lightly doped drain (LDD) structure with side-wall spacer. This phenomenon is minimized in the FOLD structure due to its higher controllability of the gate electrode than the LDD structure at the n^- extension region. Furthermore, it was also confirmed that the 0.3 μm optimized FOLD structure can achieve high circuit performance at 3.3 V operation, maintaining hot-carrier resistance     

水平管气力输送数值模拟

本文采用粒子追踪理论对水平管中粒子流动状态进行了数值模拟.文中提出了一种新的粒子碰撞模型,并忽略粒子的旋转和扬力,仅考虑气流阻力和重力对粒子的影响,在输送量为9.13×10~3kg/s,混合比约0.3的条件下,通过数值计算得知:由于粒子间的碰撞,使得异径粒子的速度趋向平均化;粒子间的碰撞是粒子悬浮的原因之一;粒子的浓度沿管轴向是随时间而发生变化的.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.