A new cladding technology to bond aluminium on magnesium

ABSTRACT

An in situ hot press bonding technology has been developed to clad aluminium on magnesium. Followed by regular hot rolling, magnesium sheets, covered by ductile and corrosion-resistant aluminium without detectable oxides in the interface, are produced. The new technology requires no welding, vacuum, protective atmosphere or barrier layer, and it makes good interfacial strength and rollability. Aluminium–magnesium intermetallic phases are formed along the clad–core interface at elevated temperatures. They are not detrimental under compression but may cause clad-core delamination in tensile strain. However, the tensile failure is more dependent on the formability of magnesium core than on the strength of interface.     

Tunable passively Q-switched thulium doped fluoride fibre (TDFF) laser using reduced graphene oxide-silver (rGO-Ag) as saturable absorber

A tunable, passively Q-switched thulium doped fluoride fibre (TDFF) laser using a reduced-graphene oxide-silver (rGO-Ag) thin film as a saturable absorber (SA) for S band operation is proposed and its efficacy demonstrated. Over a pump power range of 91.4?mW up to 158.6?mW, passively generated Q-switched pulses are observed with repetition rates from 20 to 34.5?kHz and pulse widths from 3.1 to 7.1?µs. The highest pulse energy observed is 101.2?nJ with a signal to noise ratio of ～42?dB. The proposed laser has a tuning range ～52?nm from 1458 to 1510?nm with a tunable bandpass filter (TBPF) introduced into the cavity.     

The analysis for morphological evolution and crystallography of degenerate pearlite in 100Mn13 steel

During approximate 773 K aging treatment of 100Mn13 steel, degenerate pearlite will occur and evolve into lamellar pearlite during growth process. The microstructures of degenerate pearlite and its evolutionary lamellar pearlite are observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that after 748 K, 773 K and 798 K aging, degenerate pearlites occur at grain boundary. At growth front of degenerate pearlite forming at 773 K and 798 K, pearlite presents a morphology of short lamellae of carbide and ferrite, indicating a trend of developing into lamellar pearlite. The higher the temperature is, the more obvious the trend is, and even a conventional lamellar pearlite has developed. However, there is no morphological evolution for degenerate pearlite forming at 748 K aging. Besides, the constituents of degenerate pearlite is identified as M₂₃C₆ and ferrite, and Kurdjumov-Sachs orientation relationship exists between them, (01 )_α//( 1 )_M23C6, [111]_α//[110]_M23C6. This orientation relationship maintains in morphological evolution from degenerate pearlite to lamellar pearlite.     

An evaluation of Acacia mearnsii tannin as an aluminum corrosion inhibitor in acid,alkaline, and neutral media

The electrochemical behavior of aluminum in tannin from Acacia mearnsii bark was evaluated by potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) in media under three different pH conditions: acid, alkaline, and neutral. A relationship among pH, polymerization grade (PG), zeta potential, surface, and electrochemical properties was observed in the inhibition performance of the tannin. At high pH, the oligomer structure of the tannin was affected, resulting in a low PG (4) and high zeta potential (−75 mV), and consequently, the inhibition efficiency decreased (68%) in comparison with that in acid (99%) and neutral media (96%). The values obtained indicate a physisorption mechanism for the aluminum corrosion inhibition in the studied conditions.     

Universitärer Forschungscluster „Sustainable Technologies in Metal Production and Processing” (STMP)

Foundation of a university research cluster — Co-operation along the value creation chain from raw materials to components — Evidence of joint performance offers — Utilization of synergies — Integration of Christian Doppler Laboratories — Flexible arrangement of co-operations and networks     

Reproducibility of indoor environment characteristics obtained in a walk through questionnaire. A pilot study

Walk through questionnaires may be feasible tools to obtain data on the indoor environment in community studies. However, limited information is available regarding the reproducibility of the data obtained through these questionnaires. In this pilot study, two construction engineering students inspected ten dwellings twice by means of a standardized walk through questionnaire. The two engineering students inspected the dwellings independent of each other within two months. Time between the two visits varied between 14 and 40 days. The variables presented were based on information from the residents and inspection. The continuous variables recorded included number of rooms in the dwellings, room volume, length of filled shelves and textile area. The inter- and intra-observed variabilities were poorer for number of rooms and shelf factor than for the other variables. For the 3 of the 9 categorical variables based on inspection, the inter-observer comparison showed complete agreement with a kappa statistics of 1.0, these variables being condition of the window frames and construction of outside walls and roof. One of the categorical variables showed a kappa statistics of < 0.5, these variables being presence of basement and presence of condensation at windows. This study indicates a wide variation in observer variability between various items of a walk through questionnaire. Clear definitions of all the parts of the questionnaire are needed, as well as thorough training of observers.