How to Valorize Peanut Shells by a Simple Thermal-Catalytic Method

Topics in Catalysis - In this work, a simple thermal-catalytic system was used to valorize peanut shells (Arachis hypogaea), the residual biomass from the peanut industry. To accomplish this...     

Photoelectrochemistry of poly(3-methylthiophene), I: Surface morphology and thickness effect

Photocyclovoltammetric experiments with films of poly(3-methylthiophene) under polychromatic light irradiation show a p-type semiconductor behavior in the reduced state, with a flat band potential of 0.18 V. The photocurrent depends on film thickness and surface morphology. Films with different thickness were characterized by scanning electron microscopy, indicating a globular morphology with globule sizes changing according to the charge density used during polymer deposition. The highest photocurrent is observed for the lowest globule diameter. These films were also irradiated with monochromatic light from the electrolyte side and from the substrate side. A higher photocurrent and a photocurrent spectrum matching the absorption spectrum of the reduced form of the polymer is observed on irradiation from the electrolyte side of a 0.7 μm thick film. In contrast, for irradiation from the electrode side, the photocurrent is lower and the spectrum shows a peak at lower energy. These results were interpreted in terms of a delocalized space charge zone, different kinetics for charge transfer and mass transport across the solvent swollen polymer film and different depth of penetration of the light as a function of wavelength.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Infrequent association: massive inguinoscrotal bladder hernia, multiple scrotal lithiasis, and bilateral obstructive uropathy]

BACKGROUND AND AIMS OF THE STUDY: Surgical treatment of functional tricuspid regurgitation associated with advanced valvular disease remains controversial, mainly due to the difficulty in choosing between valve replacement or reconstructive surgery. Failure to correct tricuspid regurgitation during valvular surgery carries a poor prognosis, as reoperation may represent a significant risk to the patient. Thus correct tricuspid valve surgery is vital to achieve improved early and long-term clinical results. METHODS: A total of 142 patients underwent concomitant tricuspid annuloplasty with mitral valve replacement and their clinical outcome was assessed. RESULTS: Overall hospital mortality rate was 11.3%. Seven patients died during follow up. The overall actuarial survival rate for 10 years was 74.1 +/- 14.2%. Postoperatively, 75.8% of the patients had no residual tricuspid insufficiency, while 24.2% had first- or second-degree tricuspid insufficiency and were treated medically. All patients were in NHYA functional class I or II postoperatively. CONCLUSION: Clinically, it is important to assess the severity of functional tricuspid insufficiency before and/or during the operation. Bicuspidalization annuloplasty for functional tricuspid insufficiency has provided good results, with a low incidence of reoperation and significant clinical improvement. The technique could be used in most patients with functional tricuspid regurgitation.     

Adaptive two-loop Voltage-mode control of DC-DC switching converters

A new two-loop control scheme for voltage-mode control (VMC) of dc-dc switching converters is presented. The proposed method adds a high-gain robust loop with two controllers to the conventional VMC loop, achieving an analog "adaptive" loop in which the "equivalent voltage regulator" varies with the changing power stage parameters given as follows: 1) input voltage; 2) load; and 3) component tolerances. The loop significantly improves the disturbance rejection of the control system, i.e., closed-loop output impedance and audiosusceptibility while preserving the stability and the loop gain crossover frequency to a significant extent. Both the small-signal analysis and the experimental results carried out on a buck converter demonstrate the superiority of the proposed scheme with respect to the conventional single loop.     

Graft copolymerization of different mixtures of acrylic monomers on amylopectin. Swelling behavior

Hydroxylic and nonhydroxylic acrylates—methyl acrylate (MA), ethyl acrylate (EA), butylacrylate (BA), hydroxypropyl methacrylate (HPMA), ethylenglycol dimethacrylate (EGDMA), and mixtures of HPMA–MA, HPMA–EA, HPMA–BA in a 50/50 feed composition—were grafted onto amylopectin with different amounts of crosslinking agent, EGDMA. Percent of total conversion, percent crude grafting, and influence of pH in water content were studied. In this sense it was only at pH 10 when a real variation in the water content could be seen. It was also proved that the highest values were obtained when one of the comonomers was EGDMA with a 34 mol% of the initial feed composition. © 1994 John Wiley & Sons, Inc.     

Aqueous tape casting of yttria stabilized zirconia

Tape casting process was used to produce yttria stabilized zirconia (YSZ) substrates in an aqueous system with poly(vinylalcohol) (PVA) and glycerine as binder and plasticizer, respectively. Various compositions of YSZ slips with different amounts of PVA and glycerine and consequently different solid/liquid ratios were prepared. The influence of the slip composition on the rheological properties of the slips was studied. In addition, the effect of the slip composition on the properties of the green and sintered tapes was investigated. PVA and glycerine did not affect the dispersion properties of the YSZ powder. Glycerine additions enhanced the flexibility of the green tapes but also produced a decrease in the tensile strength. The increase in the PVA content increased the tensile strength but resulted in a markedly decrease in the green density of the tapes. A correlation between the green and sintered density was found. The anisotropic sintering shrinkage parallel and perpendicular to the casting direction increased with increasing the PVA content. The slip compositions with 5 wt% PVA produced green tapes with satisfactory tensile strength. They had the highest sintered density, the lower sintering shrinkage and the lesser shrinkage anisotropy.