Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Development and evaluation of antimicrobial natamycin‐incorporated film in gorgonzola cheese conservation

Conservation of food products depends on product quality and packaging suitability. The objective of this work was to develop and evaluate the antimicrobial efficiency of natamycin‐incorporated film in the production process of Gorgonzola cheese. It aims to optimize the production process and increase shelf‐life and food safety for the consumer. Films with different concentrations of natamycin were produced and tested in Gorgonzola cheeses to evaluate its efficiency against Penicillium roqueforti on the cheese surface. Films with 2 and 4% natamycin presented satisfactory results for fungus inhibition and the amount of natamycin released to the cheese was below that allowed by the legislation. Copyright © 2006 John Wiley & Sons, Ltd.     

An over 2200-km coherent transmission experiment at 2.5 Gb/s usingerbium-doped-fiber in-line amplifiers

A 2223 km transmission distance was achieved with a 2.5-Gb/s heterodyne detection system that used erbium-doped-fiber in-line amplifiers and dispersion-shifted single-mode fibers. Twenty-five amplifiers, placed at approximately 80-km intervals, offered a total gain of more than 440 dB. Receiver sensitivity was -42.0 dBm, with only a 4.2-dB penalty from the initial sensitivity achieved by the back-to-back configuration     

Free volume and permeabilities of O2 and H2 in Nafion membranes for polymer electrolyte fuel cells

The mechanism of gas permeation in Nafion membranes for polymer electrolyte fuel cells has been investigated from the viewpoint of free volume. Three different samples, a membrane with ionic exchange capacity (IEC) = 0.92 meq/g, and recast samples with IEC = 0.92 and 1.00 meq/g were used after drying. Free volume was quantified using the positron annihilation lifetime (PAL) technique and gas permeabilities were measured for O₂ and H₂ as functions of temperature and relative humidity. Good linear correlations between the logarithm of the permeabilities at different temperatures and reciprocal free volume indicate that gas permeation in dry Nafion is governed by the free volume. Nevertheless permeabilities are much smaller than the corresponding flexible chain polymer with a similar free volume size due to stiff chains of the perfluoroethylene backbone. In highly hydrated Nafion above 60% relative humidity, where the O₂ permeability varies oppositely to the free volume, gas permeation proved to be controlled by the gradual increase in overall flexibility of the Nafion–water system.     

A Generalized Technique for Register Counting and its Application to Cost-Optimal DSP Architecture Synthesis

In this paper we propose a generalized technique to count the required number of registers in a schedule which supports overlapped scheduling and can be applied to the case where a general digit-serial data format is used. This technique is integrated into an integer linear programming (ILP) model for time-constrained scheduling. In the ILP model, appropriate processors of certain data formats are chosen from a library of processors and data format converters are automatically inserted between processors of different data formats if necessary. Then the required number of registers for each data format is evaluated correctly by the proposed technique. Hence an optimal architecture for a given digital signal processing algorithm is synthesized where the cost of registers as well as the cost of processors and data format converters are minimized. It is shown that by including the cost of registers in the synthesis task as proposed in this paper leads to up to 12.8% savings in the total cost of the synthesized architecture when compared with synthesis performed without including the register cost in the total cost.