An expert system for XPLE cable deterioration diagnosis and life forecasting

The recent increase in the demand for power in urban areas has caused changes in the way power is supplied. Underground distribution systems have been introduced for convenience in urban areas and to prevent injuries in case of a crisis. As a result, many new types of power cables are being used. One type, XPLE cables (also called CV cables) have been rapidly taking the place of conventional cables such as OF or SL cables since the 1960s because of their relatively easy installation and maintainability. However, distribution cables used under severe environmental conditions deteriorate rapidly (due mainly to water treeing), and some cables experience insulation breakdown. Therefore, many diagnostic methods have been developed, though they have not been very effective. By combining methods, a high reliability can be achieved in comparison to the use of a single method. However, processing the data is difficult for on-site personnel, so many experts are required. But there is a lack of qualified experts, hence we have turned to the development of expert systems.     

Ten-user truly asynchronous gigabit OCDMA transmission experiment with a 511-chip SSFBG en/decoder

A ten-user truly asynchronous gigabit coherent-optical-code-division-multiple-access (OCDMA) transmission was experimentally demonstrated without using any timing coordination. The enabling technologies are a record-length 511-chip superstructured-fiber-Bragg-grating (SSFBG) en/decoder and a supercontinuum (SC)-based optical-thresholding technique to significantly suppress the signal interference beat noise as well as the multiple-access-interference (MAI) noise.     

The characteristics and measuring technique of refractory dissolved organic substances in urban runoff.

It is considered that refractory dissolved organic substances have caused an increase in the COD concentration in Lake Biwa in recent years. We investigated the organic matter in the first flush of stormwater runoff from a road in the watershed area of the lake, and studied the possibility of improvement in the water environment from that aspect. After percolating the stormwater through soil, we analyzed organic substances fractionated by using GPC-TC. And we examined the effect of removal of organic substances by comparing the peak height before and after percolation. In the result of the experiments, we found that soil infiltration reduced the refractory dissolved organic substance and we successfully designed a system for a simple and easy experimental facility to treat urban runoff.     

Air trenches for sharp silica waveguide bends

Air trench structures for reduced-size bends in low-index contrast waveguides are proposed. To minimize junction loss, the structures are designed to provide adiabatic mode shaping between low- and high-index contrast regions, which is achieved by the introduction of "cladding tapers." Drastic reduction in effective bend radius is predicted. We present two-dimensional (2-D) finite-difference time-domain/effective index method simulations of bends in representative silica index contrasts. We also argue that substrate loss, while present, can be controlled with such air trenches and reduced to arbitrarily low levels limited only by fabrication capabilities. The required trench depth, given an acceptable substrate loss, is calculated in three dimensions using an approximate equivalent current sheet method and also by a numerical solver for full-vector leaky modes. A simple, compact waveguide T-splitter using air trench bends is presented.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Shear-rate dependence of first normal stress difference of poly(isoprene-b-styrene) in solution near the order-disorder transition temperature

Viscoelastic properties of poly(isoprene-b-styrene) in dioctylphthalate under steady shear flow were measured near the order—disorder transition temperature. In ordered states, first normal stress difference N₁ is proportional to shear rate at low region, but becomes proportional to at the high region, similar to the N₁ behaviour of polymer blends undergoing shear-induced homogenization. Because the existence of microdomains was confirmed at the high region by the flow birefringence method, it is concluded that the above N₁ behaviour is not caused by shear-induced homogenization, but is probably caused by the shear-induced alignment of the microdomain structure.     

Hot-water treatment of sol–gel derived SiO2–TiO2 microparticles and application to electrophoretic deposition for thick films

SiO₂–TiO₂ spherical microparticles of about 0.7 μm in diameter were prepared by the sol–gel method. Anatase nanocrystals were formed in the microparticles and their specific surface area was increased after a hot-water treatment at 90 °C. From the changes in the concentration of I₂ photocatalytically generated from KI aqueous solution, the activity of the SiO₂–TiO₂ microparticles was found to increase with increasing the hot-water treatment time. Particulate, thick films were electrophoretically deposited on indium tin oxide (ITO)-coated glass substrates using the anatase nanocrystal-precipitated SiO₂–TiO₂ microparticles. The thickness of the electrophoretically deposited particulate film increased to be approximately 10 μm with an increase in applied voltage. The resultant thick film showed a high photocatalytic activity.     

Parallel processing circuit of line image using neuristor

A simultaneous detecting circuit system of centers and lengths of some lines in one dimension is presented applying an electronic circuit model of the nervous axon with respect to signal transmission. This model consists of series of one basic section, and has functions of Neuristor. The circuit system has a paralell processing function. It is constructed by three layers. In the first layer each visual signal of lines is changed to electric pulse signal. In the second layer edges of each line are detected, and in the third layer these detected signals are converted into voltages which correspond to lengths of the lines. These functions were confirmed experimentally using its hardware.     

1.3-μm InP-InGaAsP lasers fabricated on Si substrates by waferbonding

1.3-μm InP-InGaAsP lasers have been successfully fabricated on Si substrates by wafer bonding. InP-InGaAsP thin epitaxial films are prepared by selective etching of InP substrates and then bonded to Si wafers, after which the laser structures are fabricated on the bonded thin films. The bonding temperature has been optimized to be 400°C by considering bonding strength, quality of the bonded crystal, and compatibility with device processes. Room-temperature continuous-wave (RT CW) operation has been achieved for 6-μm-wide mesa lasers with a threshold current of 39 mA, which is identical to that of conventional lasers on InP substrates. Additionally, the lasers fabricated on Si have exhibited higher output powers than the lasers on InP, which is due to higher thermal conductivity of Si substrates. From these results, the wafer bonding is thought to be a promising technique to integrate optical devices on Si and implement optical interconnections between Si LSI chips