The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Identification of osteopontin in human dental calculus matrix

Osteopontin is a prominent non-collagenous component of bone matrix, although it is expressed in several other tissues. Recently, osteopontin was reported to be involved in urinary stone formation and atherosclerotic lesions of the aorta, suggesting that it may be a key protein associated with these types of pathological mineralization. In this study, whether or not human dental calculus contains osteopontin was investigated by immunoblotting and immunohistochemical analyses. After extraction of calculus proteins with EDTA and separation of the proteins by electrophoresis, immunoblotting analysis revealed the presence of osteopontin. Two forms of osteopontin appeared at 61 and 68 kDa on 10% polyacrylamide gel and the proteins were digested with thrombin, a highly specific protease. Moreover, immunohistochemical analysis revealed that osteopontin was localized in dental calculus adherent to tooth roots. These findings indicate that osteopontin is, in fact, present in human dental calculus and may be involved in calculus formation as the stone matrix.     

The cluster of arachnoid diverticula in the occipital bone: report of two cases with literature review

The authors report two cases of multicentric osteolytic lesions in the occipital bone without any history of head trauma. The excisional biopsy of the first case revealed that the lesion was multicentric but a continuous cavity with the subarachnoid space through various sizes of dural defect, and the cavities were covered by arachnoid lining. Together with the previously reported similar 5 cases, the characteristic common feature is multicentric osteolytic lesions in the occipital bone at advanced age without marginal sclerosis. "The cluster of arachnoid diverticula in the occipital bone (CADOB)" is probably the most appropriate term for these non-traumatic lesions with the following characteristics: elderly patients, occipital bone, midline, multiple, intact outer table, nonsclerotic margin and without history of trauma. Operation may not be indicated because of its non-progressive and benign nature.     

Degradation by Sn diffusion applied to surface mounting with Ag-epoxy conductive adhesive with joining pressure

Shear and tensile tests were carried out on joints made with an isotropic conductive adhesive (ICA) consisting of Ag and epoxy: Sn–Pb plated components mounted on printed boards and tensile bars consisting of Sn plated Ni and Cu joined under various joining pressures. After 150 °C–100 h, shear strength degraded to 72% and Sn in the plating diffused slightly to the Ag fillers in the ICA for the component mounting. High joining pressure increased the initial tensile strength and volume percentage of Ag fillers in the ICA. After 150 °C–100 h, tensile strengths for all joining pressures degraded on average to 36% of the initial strengths. In the case of low joining pressures, an Ag–Sn intermetallic was formed at only the Ag–Sn contact points of the Sn/ICA interface; leading to reproducibility of the component mounting. The difference of degradation ratios between the mounted components and tensile bars could be explained by the offset of the Sn–Pb area at the component/ICA interface.     

Real-time 3-D model-based navigation system for endoscopicparanasal sinus surgery

This paper presents a three-dimensional (3-D)-model-based navigation system for endoscopic sinus surgery treating paranasal sinusitis. Endoscopic surgery is becoming more common because of its low invasiveness. Its problem with disorientation, however, is one of the toughest barriers for the novice and may lead even an expert to commit serious surgical errors, e.g., causing cerebrospinal fluid (CSF) leakage or blinding the patient. To prevent such complications and optimize training, the authors' system aids in navigation by showing a single perspective view of the patient and the endoscope models. This virtual endoscope has a viewing cone with a simulated light to indicate the viewing direction and visual field in real-time. The system's three clipping planes automatically follow the endoscope and help keep the surgeon aware of the endoscope's actual position. An experiment comparing the system to conventional navigation using a triplanar display showed that the perspective view was referenced very frequently, giving a positive impressions, while the triplanar display was almost completely ignored, apparently because it was too difficult to interpret immediately     

Postgrowth Annealing of CdTe Layers Grown on Si Substrates by Metalorganic Vapor-Phase Epitaxy

Annealing conditions of CdTe layers grown on Si substrates by metalorganic vapor-phase epitaxy were studied. Typically, 3-μm-thick n-type (211) CdTe layers were annealed for 60 s in flowing hydrogen at atmospheric pressure by covering their surfaces with bulk CdTe wafers. At annealing temperatures above 700°C, improvement of crystal quality was confirmed from full-width at half-maximum values of double-crystal rocking-curve measurements and x-ray diffraction measurements. Photoluminescence measurements revealed no deterioration of electrical properties in the annealed n-CdTe layers. Furthermore, annealing at 900°C improved the performance of radiation detectors with structure of p-like CdTe/n-CdTe/n ⁺-Si substrate.     

A 1.3-GHz fifth-generation SPARC64 microprocessor

A fifth-generation SPARC64 processor is fabricated in 130-nm partially depleted silicon-on-insulator CMOS with eight layers of Cu metallization. At V/sub dd/ = 1.2 V and T/sub a/ = 25/spl deg/C, it runs at 1.3 GHz and dissipates 34.7 W. The chip contains 191 M transistors with 19 M logic circuits in an area of 18.14 mm /spl times/ 15.99 mm and is covered with 5858 bumps, of which 269 are for I/O signals. It is mounted in a 1360-pin land-grid-array package. The 16-byte-wide system bus operates with a 260-MHz clock in single-data-rate or double-data-rate modes. This processor implements an error-detection mechanism for execution units and data path logic circuits in addition to on-chip arrays to detect data corruption. Intermittent errors detected in execution units and data paths are recovered via instruction retry. A soft barrier clocking scheme allows amortization of the clock skew and jitter over multiple cycles and helps to achieve high clock frequency. Tunability of the clock timing makes timing closure easier. A relatively small amount of custom circuit design and the use of mostly static circuits contributes to achieve short development time.     

A theoretical discussion on the foundation of Stone??s blind source separation

This paper discusses the theoretical foundation of Stone’s BSS (Stone in Neural Comput 13:1559–1574, 2001; Stone in Independent Component Analysis: A Tutorial Introduction, A Bradford Book, London, 2004), and it proposes a novel BSS approach based on second-order statistics of the responses of two different linear filters to source signals. The proposed approach which includes Stone’s BSS as a special case helps us to understand how generalized eigenvalue decomposition (GEVD) concludes separating vectors in Stone’s BSS. It obtains the separating vectors by simultaneous diagonalization of covariance matrices of two different linear filters responses to the mixtures. The two employed linear filters are selected dependent on source signals structures under the assumption that they have different responses to source signals. Here, two FIR filters with coefficients selected in an opposite probabilistic way have been suggested for the proposed BSS. The proposed BSS method has been compared with Stone’s BSS, SOBI and AMUSE over speech and image mixtures in different noise levels.