Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

Effect of hot pressing on processing and properties of BBN ceramics

BBN (BaBi₂Nb₂O₉) is very interesting and promising lead free material with relaxor properties in capacitors, sensors and actuators.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Topical use of aprotinin in open heart operations

Among various pharmacological agents used to reduce bleeding after open-heart operations, high-dose aprotinin therapy seems most promising. However, its long-term effects are still obscure; there is almost always possibility of bypass graft occlusions produced by the hypercoagulable state induced by aprotinin in coronary bypass operations. Topical application of aprotinin into the pericardial cavity could prevent the adverse effects. Fifty patients were prospectively studied to evaluate the effects of topical aprotinin. One million KIU of aprotinin was poured into the pericardial cavity before closure of the sternotomy in group 1 (n = 25). Patients in group 2 (n = 25) served as controls. Total postoperative bleeding was significantly reduced in group 1 when compared with that of group 2 (722.7 +/- 230.8 versus 1,282.6 +/- 225.7 mL; p < 0.01). The use of banked donor blood products was significantly less in group 1 than in group 2 (0.33 +/- 0.67 versus 1.36 +/- 0.86 units; p < 0.01). These results show that topical use of aprotinin reduces post-operative blood loss and need for transfusion. It seems promising and warrants further studies to be done.     

Analytical determination of intrinsic permeability of synthetic nonwoven filter fabrics

In this paper an analytical method for determining the permeability of nonwoven filter fabrics is presented. The derived formula shows that the intrinsic permeability, fully characterizing the porous medium, depends on fabric porosity, n, fibre diameter, d, and a shape factor determined experimentally.     

Influence of the amount of ferromagnetic addition on the rheological properties of spinning solutions,the structure,the strength,and thermal properties of polyacrylonitrile fibres

The rheological properties of spinning solutions of polyacrylonitrile in dimethyl formamide (DMF) containing various amounts of a ferromagnetic nanoaddition were investigated. The porous structure, the strength and thermal properties of fibers obtained from these solutions were assessed, as well as the uniformity of the nanoaddition distribution on the fiber surface was estimated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Potentiometric studies of oxidation–reduction reactions with redox copolymers

Polymeric oxidants in the bead form that were macroporous styrene/divinylbenzene copolymers containing N‐chlorosulfonamide functional groups (in sodium or hydrogen form) or N‐bromosulfonamide groups (in sodium form) were synthesized and investigated to determine their oxidizing powers. The redox potentials of the N‐chlorosulfonamide/sulfonamide and N‐bromosulfonamide/sulfonamide systems were determined by potentiometric studies at different pH values with aqueous solutions of Na₂SO₃, KCN, and KSCN as reducers. The formal redox potentials of the N‐chlorosulfonamide copolymers were 0.79, 0.44, and ?0.12 V at pH's of 1.8, 8.45, and 13.6, respectively. The formal redox potential of the N‐bromosulfonamide copolymer was about 100 mV higher in comparable conditions and in solutions over pH = 5 (e.g., 0.56 V at pH = 8.56). The comparatively higher oxidizing power of the N‐bromosulfonamide copolymer was particularly evident in a strong alkaline medium (in which the N‐chlorosulfonamide copolymer was not reactive). In contrast, the N‐chlorosulfonamide copolymer showed strong oxidative properties in acidic media (in which the N‐bromosulfonamide copolymer decomposed itself). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008