Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Power Distribution Fault Cause Identification With Imbalanced Data Using the Data Mining-Based Fuzzy Classification E-Algorithm

Power distribution systems have been significantly affected by many outage-causing events. Good fault cause identification can help expedite the restoration procedure and improve the system reliability. However, the data imbalance issue in many real-world data sets often degrades the fault cause identification performance. In this paper, the E-algorithm, which is extended from the fuzzy classification algorithm by Ishibuchi to alleviate the effect of imbalanced data constitution, is applied to Duke Energy outage data for distribution fault cause identification. Three major outage causes (tree, animal, and lightning) are used as prototypes. The performance of E-algorithm on real-world imbalanced data is compared with artificial neural network. The results show that the E-algorithm can greatly improve the performance when the data are imbalanced     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators     

The maximum bit rates of soliton communication systems with lumpedamplifiers and filters in different distances

The maximum bit rate of a soliton communication system with lumped amplifiers and optical filters is considered. When the dispersion of the fiber varies from one amplifier spacing to another amplifier spacing, the maximum bit rate is significantly reduced. To overcome the effect, the amplitude of the soliton is amplified so that it is still the average soliton corresponding to the fiber dispersion for an amplifier spacing. Thus, the maximum bit rate is only slightly less than that without the dispersion variations. For a given distance, the maximum bit rate limited by the stability and soliton interaction is obtained. The result is compared with that limited by the Gordon-Haus effect. For shorter transmission distance, the maximum bit rate is limited by the stability and soliton interaction. For longer transmission distance, the maximum bit rate is limited by the Gordon-Haus effect     

我国聚甲醛工业的供需分析

从国内聚甲醛树脂的生产、贸易及消费状况出发 ,分析了国内聚甲醛工业的供需现状并提出短期预测。     

Simple approximations of the DC flux influence on the core losspower electronic ferrites and their use in design of magnetic components

The effect of DC flux on the core loss is examined for the practical range of power and frequency. Relevant core loss equations are derived and applied to an optimization algorithm to determine the minimum core loss at a given ratio of s (DC flux density to AC peak flux density). It has been found that the curves of hysteresis loss density versus the ratio of s exhibit a peak at a critical ratio. Below or above this critical ratio, the loss density decreases drastically. On the other hand, the curves of eddy-current loss density versus the ratio of s exhibits a minimum point at a critical ratio. Below or above this critical ratio, the loss density increases gradually     

Performance evaluation of a multichannel transceiver system forADSL and VHDSL services

The authors study the performance of a multichannel modulation method for asymmetric digital subscriber lines (ADSLs) and very high-speed digital subscriber lines (VHDSLs). In the ADSL case, over all unloaded North American subscriber lines in the test set, a unidirectional 1.536 Mb/s data rate service from the end office to the customer premises is possible on a single twisted pair at an error rate of 10^-7 with at least a 6 dB margin used coded multichannel modulation with sufficient transmit power. In the VHDSL case, data rates in excess of 100 Mb/s can be transmitted reliably, at an error rate of 10^-7, using uncoded multichannel modulation on a single twisted pair over a distance ⩽150 ft with a sufficiently high sampling rate (≈24 MHz) and transmit power. It is shown that a cost-effective multichannel transceiver design suggested for high-speed digital subscriber line (HDSL) service will also work well for ADSL and VHDSL services with only minimal modifications     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

A simplified method for calculating the substation grounding gridresistance

A simple and accurate formula for calculating the grounding grid resistance is proposed in this paper. This method is based on a theoretical manipulation of the numerical moment method and of the current image. The formula is dependent on the substation grounding grid design, such as grid depth, grid size, number of meshes, grid-conductor diameter, etc. A comparison study is performed to check the accuracy of the proposed formula with respect to six different formulas and methods in the literature. An excellent agreement was found between the results of this formula and the results of a sophisticated computerized method