Densification involved in the UV-based photosensitivity of silicaglasses and optical fibers

A comprehensive survey of photosensitivity in silica glasses and optical fiber is reviewed. Recent work on understanding the mechanisms contributing to germanium or aluminum doped fiber photosensitivity is discussed within the framework of photoelastic densification models     

新型实用布线算法──L─M算法

本文提出新型布线算法，集李氏迷宫法与线搜索法的长处为一体，以饱和带法进行动态排序，以线搜索法确定借孔位置，然后用李氏法进行单层布线，获得最佳路径，从而达到线型好，布通率高的效果。     

环境中氚和碳-14

本文介绍了加拿大恰克河实验室有关氚和碳－14在环境中行为和评价的研究。     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

非线性系统鲁棒吸引的动态补偿方法

考虑非线性不确定系统的鲁棒吸引问题,借助于动态输出反馈,构造了两类控制律。这两类控制律分别可使相应的闭环系统被一任意小的区域鲁棒吸引,或被一预先设置的区域有限吸引。     

The importance of electrochemistry-related etching in thegate-groove fabrication for InAlAs/InGaAs HFETs

For the first time, the surface metal on nonalloyed ohmic electrodes is found to significantly change the profiles of gate grooves, when resist openings are employed to monitor drain current during wet-chemical gate recess for sub-micron InAlAs/lnGaAs heterojunction field-effect transistors (HFETs). The surface metal of Ni enhances the etching rate in comparison with that in the absence of electrodes by a factor of 4 and 10, laterally and vertically, which is favorable to fabricate deep gate grooves with small side etching. The Pt surface metal, however, leads to preferential etching of InGaAs over InAlAs, which can be useful to realize large side etching. The existence of an electrochemistry-related etching component, which arises when the ohmic electrodes are present during recess etching, is considered to be responsible for these behaviors