Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

An image processing system using Image Signal Multiprocessors (ISMPs)

This paper describes an image processing system using Image Signal Multiprocessors (ISMPs) adapted to gray-level image preprocessing for image analysis and image enhancement. It is composed of four ISMPs, five 1H-delay-lines, two 512×512×8-bit frame memories, a video timing controller (VTC), two 256-word ×8-bit ×8-table Look Up Tables (LUTs) and 80 nsec/sampling A/D and D/A converters. This multiprocessor system performs convolution operations such as spatial filters, contrast enhancement, and binarization for gray-level images, thinning, thickening, pattern matching etc. for binary images, and image quality improvement for moving images such as T.V. images. Otherwise, it performs feature extraction operations such as area calculations, fillet coordination, and moment calculations for objective image data. Moreover, this system is capable of applying color image processing by using a multiboard system.     

Crystallization process and magnetic properties of Fe100−x,B x (10 ≦ × ≦ 35) amorphous alloys and supersaturated state of boron inα-Fe

Amorphous specimens of Fe_100–x B _x were prepared in the range 10 × 35 at % B by a single-roller method. The crystallization process and the boron concentration dependence of the Curie temperature were examined by differential scanning calorimetry, X-ray diffraction, Mössbauer spectroscopy and magnetic measurements. Two-step crystallization was observed in specimens with× < 17: amorphous amorphous + boron-supersaturated b c c phase (-Fe(B)) t-Fe₃B +-Fe. A single-Fe(B) phase was not observed. The transition temperature from t-Fe₃B to stable (-Fe + t-Fe₂B) sensitively depends on the boron content in the alloys. The crystallization temperature (T _x) of the amorphous alloys was almost unchanged for 17 × 31, but increased remarkably at high boron concentrations of× 33, where the decomposition products consisted of t-Fe₂B and o-FeB. The Curie temperature (T _c) of the amorphous phase was as low as 480 K at× = 10, increased with increasing boron content up to 820 K and then decreased in the high boron concentration alloys of× > 28. A single-Fe(B) phase was not detected in the as-quenched specimens of× = 8 and 10. The phase coexisted with the o-Fe₃B and amorphous phases. The lattice parameter of the phase was 0.2861₀ nm which was smaller than that of pure iron by 2/1000, indicating the substitutional occupation of boron atoms in the b c c lattice.     

Detection of environmental changes from network structure

We studied the networks of the temperature record in the atmosphere. They are made by the strength of the synchronization, including the delay between temperatures at locations on Earth. We consider these locations as nodes, and we consider a pair of locations as a link if the synchronization between them is stronger than a threshold. The network is scale-free, which is thought to contribute to the stability of the climate. This work was presented in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Enzymatic production of pyrimidine nucleotides using Corynebacterium ammoniagenes cells and recombinant Escherichia coli cells: enzymatic production of CDP-choline from orotic acid and choline chloride (Part I)

Enzymatic production of cytidine diphosphate choline (CDP-choline) using orotic acid and choline chloride as substrates was investigated using a 200-ml beaker as a reaction vessel. When Cornybacterium ammoniagenes KY13505 cells were used as the enzyme source, UMP was accumulated up to 28.6 g/liter (77.6 mM) from orotic acid after 26 h of reaction. In this reaction, UDP and UTP were also accumulated, but CTP, a direct precursor of CDP-choline, was not accumulated sufficiently. Escherichia coli JF646/pMW6 cells, which overproduce CTP synthetase by selfcloning of the pyrG gene, were used together with cells of KY12505 for the enzymatic reaction using orotic acid as a substrate. CTP was produced at 8.95 g/liter (15.1 mM) after 23 h of this reaction. To produce CDP-choline, two additional enzyme activities were needed. E. coli MM294/pUCK3 and MM294/pCC41 cells, which express a choline kinase from Saccharomyces cerevisiae (CKIase; encoded by the CKI gene) and a cholinephosphate cytidylyltransferase from S. cerevisiae (CCTase; encoded by the CCT gene) respectively, were added to this CTP-producing reaction system. After 23 h of the reaction using orotic acid and choline chloride as substrates, 7.7 g/liter (15.1 mM) of CDP-choline was accumulated without addition of ATP or phosphoribosylpyrophosphate (PRPP). ATP and PRPP required in the CDP-choline forming reaction system are biosynthesized by those cells using glucose as a substrate.     

Inorganic/Organic Double‐Network Gels Containing Ionic Liquids

Highly robust ion gels, termed double‐network (DN) ion gels, composed of inorganic/organic interpenetrating networks and a large amount of ionic liquids (ILs), are fabricated. The DN ion gels with an 80 wt% IL content show extraordinarily high mechanical strength: more than 28 MPa of compressive fracture stress. In the DN ion gel preparation, a brittle inorganic network of physically bonded silica nanoparticles and a ductile organic network of polydimethylacrylamide (PDMAAm) are formed in the IL. Because of the different reaction mechanisms of the inorganic/organic networks, the DN ion gels can be formed by an easy and free‐shapeable one‐pot synthesis. They can be prepared in a controllable manner by manipulating the formation order of the inorganic and organic networks via not only multistep but also single‐step processes. When silica particles form a network prior to the PDMAAm network formation, DN ion gels can be prepared. The brittle silica particle network in the DN ion gel, serving as sacrificial bonds, easily ruptures under loading to dissipate energy, while the ductile PDMAAm network maintains the shape of the material by the rubber elasticity. Given the reversible physical bonding between the silica particles, the DN ion gels exhibit a significant degree of self‐recovery by annealing.     

含大剂量功能性油剂的热塑性聚合物母粒SROPE

SROPE技术是用加入第三组分嵌段聚合物的方法使大剂量的功能性油剂混入热塑性聚合物中,制成具有油剂缓慢析出性能的母粒,可赋予聚合物一定的功能性。SROPE技术对于几乎所有的模压和熔融纺丝工艺都有相当广泛的通用性。     

Pinpoint injection of microtools for minimally invasive micromanipulation of microbe by laser trap

This paper reports transportation of the target microbe by the laser trapped microtools with minimum laser irradiation to the target. The size of a microtool (MT) is around micrometer. The MTs are manipulated by the focused laser under the microscope to manipulate the target microbe. Here we propose a pinpoint injection method of MTs at the desired location in the microchamber, which is filled with liquid. At first, we classified the injection method of the MTs in four categories. Here we employed a new method to install the MTs inside the microchamber. We developed a MT holding chip to install the MTs. The MTs were injected in the microchamber, and were manipulated successfully by the laser scanning micromanipulator to transport the target microbe for separation. The proposed method is useful for the pinpoint injection of MTs and separation by the indirect micromanipulation.