全文获取类型
收费全文 | 330篇 |
免费 | 18篇 |
国内免费 | 5篇 |
专业分类
电工技术 | 1篇 |
综合类 | 2篇 |
化学工业 | 73篇 |
金属工艺 | 10篇 |
机械仪表 | 3篇 |
建筑科学 | 19篇 |
矿业工程 | 3篇 |
能源动力 | 9篇 |
轻工业 | 46篇 |
水利工程 | 5篇 |
石油天然气 | 6篇 |
无线电 | 25篇 |
一般工业技术 | 64篇 |
冶金工业 | 38篇 |
原子能技术 | 1篇 |
自动化技术 | 48篇 |
出版年
2023年 | 11篇 |
2022年 | 20篇 |
2021年 | 24篇 |
2020年 | 13篇 |
2019年 | 13篇 |
2018年 | 19篇 |
2017年 | 15篇 |
2016年 | 12篇 |
2015年 | 11篇 |
2014年 | 12篇 |
2013年 | 19篇 |
2012年 | 16篇 |
2011年 | 20篇 |
2010年 | 19篇 |
2009年 | 8篇 |
2008年 | 19篇 |
2007年 | 13篇 |
2006年 | 11篇 |
2005年 | 9篇 |
2004年 | 7篇 |
2003年 | 8篇 |
2002年 | 3篇 |
2001年 | 2篇 |
2000年 | 5篇 |
1999年 | 2篇 |
1998年 | 9篇 |
1997年 | 3篇 |
1996年 | 3篇 |
1995年 | 2篇 |
1993年 | 1篇 |
1991年 | 1篇 |
1988年 | 3篇 |
1987年 | 1篇 |
1986年 | 1篇 |
1985年 | 3篇 |
1984年 | 2篇 |
1983年 | 4篇 |
1981年 | 1篇 |
1980年 | 1篇 |
1979年 | 2篇 |
1976年 | 1篇 |
1975年 | 2篇 |
1972年 | 1篇 |
1967年 | 1篇 |
排序方式: 共有353条查询结果,搜索用时 0 毫秒
1.
The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation. 相似文献
2.
This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance. 相似文献
3.
This article describes the fundamental foaming mechanisms that governed the volume expansion behavior of extruded polypropylene (PP) foams. A careful analysis of extended experimental results indicated that the final volume expansion ratio of the extruded PP foams blown with butane was governed by either the loss of the blowing agent or the crystallization of the polymer matrix. A charge coupling device (CCD) camera was installed at the die exit to carefully monitor the shape of the extruded PP foams. The CCD images were analyzed to illustrate both mechanisms, gas loss and crystallization, during foaming at various temperatures, and the maximum expansion ratio was achieved when the governing mechanism was changed from one to the other. In general, the gas loss mode was dominant at high temperatures and the crystallization mode was dominant at low temperatures. When the gas loss mode was dominant, the volume expansion ratio increased with decreasing temperature because of the reduced amount of gas lost. By contrast, when the crystallization mode was dominant, the expansion ratio increased with increasing temperature because of the delayed solidification of the polymer. The processing window variation with the butane concentration, the change in the temperature ranges for the two governing modes, and the sensitivity of melt temperature variations to the volume expansion ratio are discussed in detail on the basis of the obtained experimental results for both branched and linear PP materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2661–2668, 2004 相似文献
4.
Thin‐film encapsulated white organic light top‐emitting diodes using a WO3/Ag/WO3 cathode to enhance light out‐coupling 下载免费PDF全文
Karim Bouzid Tony Maindron Hani Kanaan 《Journal of the Society for Information Display》2016,24(9):563-568
An alternative design of a semitransparent cathode for top‐emission white‐fluorescent organic light‐emitting diodes (OLEDs) has been investigated. The scope of this study was to improve the luminance of OLEDs used for displays while keeping the current density versus voltage characteristic unchanged for addressing purposes. The use of an optical simulation tool allowed the optimization of the tri‐layer cathode WO3/Ag/WO3 to increase the light out‐coupling coefficient of the device leading to an increased white emission compared with a reference device with a Ca/Ag cathode. An increase of ~40% in luminance has been calculated by simulation and experimentally confirmed. The p‐i‐n OLED structure underneath the tri‐layer cathode allowed an efficient injection of electrons independently from the work function of WO3. The WO3/Ag/WO3 cathode has been also confirmed to be compatible with the atomic layer deposition technique for thin film encapsulation. Finally, lifetime measurements up to 600 h have been carried out to quantify the enhancements induced by the new cathode compared with the control device. It has been found that lifetimes of both cathode architectures are similar on this time scale, while the WO3/Ag/WO3 cathode shows a lower voltage drift versus aging. 相似文献
5.
The application of titanium dioxide (TiO(2)) films as surgical implant coatings for antibiotic attachment depends crucially on their available surface area and thus their surface morphology and crystallinity. Here, we report our fabrication of high Wenzel ratio TiO(2) films targeted to increase the film surface area using the ion beam-assisted deposition (IBAD) technique at high-deposition temperatures (approximately 610 degrees C). The modulation of the films' surface morphology was accomplished by varying the chemical identity of the concurrent ion beams bombarded on the films during the e-beam evaporation process. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were employed to investigate the surface morphology of the as-deposited films. X-ray diffractometry (XRD) revealed that these nanocrystalline films primarily consist of anatase phase TiO(2). Wenzel ratio, the ratio of the actual surface area to the projected area, of IBAD films prepared with argon, oxygen, and nitrogen ion beams was measured to be 1.52, 1.31 and 1.49, respectively. The effect of the differences in chemical reactivity and ion size of these three type ion beams are discussed to explain the present results. 相似文献
6.
Nowadays, tandem structures have become a valuable competitor to conventional silicon solar cells, especially for perovskite over silicon, as metal halides surpassed Si with tunable bandgaps, high absorption coefficient, low deposition, and preparation costs. This led to a remarkable enhancement in the overall efficiency of the whole cell and its characteristics. Consequently, this expands the usage of photovoltaic technology in various fields of applications not only under conventional light source spectrum in outdoor areas, i.e., AM1.5G, but also under artificial light sources found indoors with broadband intensity values, such as Internet of things (IoTs) applications to name a few. We introduce a numerical model to analyze perovskite/Si tandem cells (PSSTCs) using both crystalline silicon (c-Si) and hydrogenated amorphous silicon (a-Si:H) experimentally validated as base cells. All proposed layers have been studied with J-V characteristics and energy band diagrams under AM1.5G by using SCAPS-1D software version 3.7.7. Thereupon, the proposed architectures were tested under various artificial lighting spectra. The proposed structures of Li4Ti5O12/CsPbCl3/MAPbBr3/CH3NH3PbI3/Si recorded a maximum power conversion efficiency (PCE) of 25.25% for c-Si and 17.02% for a-Si:H, with nearly 7% enhancement concerning the Si bare cell in both cases. 相似文献
7.
In this paper, two computationally efficient algorithms are presented for determining the least possible time paths for all origins to a single destination in networks where the arc weights are discrete random variables whose probability distribution functions vary with time. The first algorithm determines the least possible time path from each node for each departure time interval, the least possible travel time and a lower bound on the associated probability of the occurrence of this travel time. The second algorithm determines up to k least possible time paths, the associated travel times and the corresponding probabilities of occurrence of the travel times (or a lower bound on this probability). No such efficient algorithms for determining least time paths in stochastic, time-varying networks exist in the literature. 相似文献
8.
The mechanism(s) of insulin resistance in non-insulin-dependent diabetes mellitus remains ill defined. The current studies sought to determine whether non-insulin-dependent diabetes mellitus is associated with (a) a delay in the rate of onset of insulin action, (b) impaired hepatic and extrahepatic kinetic responses to insulin, and (c) an alteration in the contribution of gluconeogenesis to hepatic glucose release. To answer these questions, glucose disappearance, glucose release, and the rate of incorporation of 14CO2 into glucose were measured during 0.5 and 1.0 mU/kg-1 per min-1 insulin infusions while glucose was clamped at approximately 95 mg/dl in diabetic and nondiabetic subjects. The absolute rate of disappearance was lower (P < 0.05) and the rate of increase slower (P < 0.05) in diabetic than nondiabetic subjects during both insulin infusions. In contrast, the rate of suppression of glucose release in response to a change in insulin did not differ in the diabetic and nondiabetic subjects during either the low (slope 30-240 min:0.02 +/- 0.01 vs 0.02 +/- 0.01) or high (0.02 +/- 0.00 vs 0.02 +/- 0.00) insulin infusions. However, the hepatic response to insulin was not entirely normal in the diabetic subjects. Both glucose release and the proportion of systemic glucose being derived from 14CO2 (an index of gluconeogenesis) was inappropriately high for the prevailing insulin concentration in the diabetic subjects. Thus non-insulin-dependent diabetes mellitus slows the rate-limiting step in insulin action in muscle but not liver and alters the relative contribution of gluconeogenesis and glycogenolysis to hepatic glucose release. 相似文献
9.
10.
Lim Swee Su Chong Poh She Jong Bor Chyan Abu Bakar Mimi Hani Wan Daud Wan Ramli Md. Jahim Jamaliah Salehmin Mohd Nur Ikhmal 《Journal of Applied Electrochemistry》2022,52(9):1327-1342
Journal of Applied Electrochemistry - A microbial fuel cell (MFC) is an electricity-generating device utilising electrochemically active microorganisms as biocatalysts. Using MFC as a biosensor to... 相似文献