Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Effect of modified atmosphere packaging on the shelf-life of coated, whole and sliced mushrooms

Whole and sliced fresh mushrooms (Agaricus bisporus) were packaged with PVC wrap or two polyolefins (PD-941 and PD-961) films after coating with CaCl₂ and chitosan. Package gas composition, color, weight loss and maturity were measured during storage at 12 °C and 80%RH. For PD-961, the highest in-package concentration occurred during the first day of storage regardless of treatments, while wrap and PD-941 showed varying degrees in-package concentration with different processes and coatings. The whiteness of whole mushrooms varied significantly with the type of coating, but not with the type of films. The extent of darkening was greater in coated whole mushrooms than in sliced ones. Weight loss occurred in all packages and varied from 3 (g/100 g) to about 7 (g/100 g) after 6 days of storage. Due to a lower permeability, PD-961 packages had the lowest weight loss. The type of packaging films significantly affected the maturity index, where PD-961 most effectively lowered maturity index for both whole and sliced mushrooms, thus extending the shelf-life. The type of coating did not appear to affect maturity index except for the wrap package where chitosan coating markedly lowered the maturity index of sliced mushrooms.     

Solid phase crystallization of amorphous silicon on glass by thin film heater for thin film transistor (TFT) application

A new process for solid phase crystallization (SPC) of amorphous silicon (a-Si) using thin film heater is reported. With this localized Ti silicide thin film heater, we successfully crystallized 500 Å-thick a-Si in a few minutes without any thermal deformation of glass substrate. The size of crystallized silicon grain was abnormally big (30-40 μm). Polycrystalline thin film transistors (TFT) fabricated using this unique thin film heater showed better mobility than those of conventional ones by furnace annealing.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Design and practical implementation of multifrequency RF front ends using direct RF sampling

The use of direct RF sampling has been explored as a means of designing multifrequency RF front ends. Such front ends will be useful to multifrequency RF applications such as global navigation satellite system receivers that use global positioning system (GPS) L1, L2, and L5 signals and Galileo signals. The design of a practical multifrequency direct RF sampling front end is dependent on having an analog-to-digital converter whose input bandwidth accommodates the highest carrier frequency and whose maximum sampling frequency is more than twice the cumulative bandwidth about the multiple carrier signals. The principle of direct RF sampling is used to alias all frequency bands of interest onto portions of the Nyquist bandwidth that do not overlap. This paper presents a new algorithm that finds the minimum sampling frequency that avoids overlap. This design approach requires a multifrequency bandpass filter for the frequency bands of interest. A prototype front end has been designed, built, and tested. It receives a GPS coarse/acquisition code at the L1 frequency and GPS antispoofing precision code at both L1 and L2. Dual-frequency signals with received carrier-to-noise ratios in excess of 52 dB-Hz have been acquired and tracked using this system.     

Dye adsorption characteristics of alginate/polyaspartate hydrogels

This study examined the removal of some basic dyes, such as Methylene Blue, Malachite Green and Methyl Orange, using alginate or alginate/polyaspartate composite gel beads. The adsorption of dyes from aqueous solutions at 25 °C was examined using a batch sorption technique. The effects of CaCl₂ and the dye concentration on the adsorption were examined. Type-S adsorption isotherms were obtained, which is characteristic of a weak solute–solid interaction. The ionic interaction between the dye molecule and gel matrix appears to be responsible for the efficient adsorption of cationic dyes in this system. These results suggest that an alginate/polyaspartate gel can be used as an effective sorbent for water pollutants such as dyes, and the immobilization of these organic contaminants in the hydrogels from wastewater can solve one of the most important environmental problems in the related industry.