Analysis of integrated optical waveguide mirrors

A new method is presented to analyze reflection losses of integrated mirrors, taking into account the exact guided mode profile and assuming that this profile remains unchanged up to the reflecting plane. The fraction of the reflected light coupled to one of the guided modes of the output waveguide is calculated, taking into account the mirror reflection coefficient. The influence of both translation and tilt of the reflecting plane is investigated. The method applies for every guided mode and any reflection angles. Numerical calculations are derived for a 90° optical corner mirror     

Changes in the dielectric relaxations of water in epoxy resin as a function of the extent of water ingress in carbon fibre composites

Dielectric relaxation measurements are reported over a frequency range from 10⁻¹ to 10⁹ Hz as a function of exposure time for an epoxy resin-carbon fibre composite, ageing at 60 °C in water. Investigation of the nature of the dipole relaxation of the water molecules, indicates the nature of their interaction with the polymer matrix. Analysis of the dielectric relaxation spectra allow identification of processes that can be attributed to ‘free’ and ‘bonded’ water, water in micro-cracking, located in carbon fibre disbonds and plasticizing the polymer matrix. Identification of the various types of location in which water exists was aided by use of the N_g factor from the Kirkwood-Frölich equation, which describes the constraints on free dipole ration nature imposed by the environment in which it is located. These data indicate the power of the dielectric technique for quantitative analysis of water ingress into epoxy composites.     

Influence of wood extractives on the photo‐discoloration of wood surfaces exposed to artificial weathering

Extracted and unextracted black cherry (Prunus serotina), red oak (Quercus rubra), and red pine (Pinus resinosa) wood specimens were exposed to artificial weathering, and their discoloration process was investigated to obtain basic understanding on the role of wood extractives in the weathering of hardwoods and softwoods. Color measurements were made with a spectrometer according to ISO 2470 standards, using the CIELAB system. Results obtained showed that the rate of whiteness was not significantly affected by extractives removed with organic solvents, but were significantly affected when organic solvent extraction was followed by water extraction. The total discoloration rate had the same pattern, and chromaticity coordinates were less affected by wood extractives. These results confirm the hypothesis that some extractives contained in wood act as antioxidants and are able to provide some protection to wood surfaces against weathering degradation. However, more work is needed to understand the chemistry and mechanism of action of these extractives so as to develop any practical use for this property. © 2006 Wiley Periodicals, Inc. Col Res Appl, 31, 425–434, 2006; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20248     

Development of poly(vinyl chloride)/wood composites. A literature review

Poly(vinyl chloride)/wood fiber (flour) composites are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles, decking, railing, and siding by using conical counterrotating intermeshing twin‐screw extruders. Heat stabilizers, processing aids, impact modifiers, lubricants, and pigments are still important for PVC/wood composite formulations. Poly[methylene(polyphenyl isocyanate)] (PMPPIC), γ‐aminopropyltriethoxysilane, maleated polypropylene (MAPP), and copper metallic complex have proved to be effective coupling agents for this composite system. Mechanical properties of PVC/wood composites can be enhanced by combining wood with mica or glass fibers to form hybrid reinforcements. Ultraviolet light resistance and weathering dimensional stabilities of PVC/wood composites are superior to those of natural wood. Density reduction can be achieved through the microcellular foaming technique by using chemical blowing agents, such as azodicarbonamide and sodium bicarbonate, or physical blowing agents, such as carbon dioxide. J. Vinyl Addit. Technol. 10:59–69, 2004. © 2004 Society of Plastics Engineers.     

Alkaline fuel cells: contemporary advancement and limitations

ZeTek Power recently introduced mass manufacturable and cost effective alkaline fuel cells on the market. Today's research is focused on further improvement both in terms of performance increase and cost reduction. This research is classically performed using small (4 cm²) experimental electrodes in the half-cell configuration. This allows the primary electrochemical losses in an anode or cathode to be determined independently. Additional performance losses occur when one integrates large electrodes into a module of 24 cells and in a stack comprised of many modules. By comparing the performance of half-cell experiments to that of modules, these losses can be distinguished and addressed. The information thus obtained, both for the small electrodes and in up-scaling is vital if one is to identify the key areas in which improvement is possible and where to focus future research. Furthermore, the identification of the losses in a module and system allows us to predict the final performance from half-cell measurements of a new laboratory scale experimental electrode.     

Determination of the repartition of monomers between sol and gel fractions in copolycondensate glycerol/azelaic acid by radioassay

The distribution of the monomers between sol and gel fractions, theoretically forecasted from network formation theory, is experimentally determined in glycerol/azelaic acid system with tritium labeled glycerol by radioassay.Presented at the 7th Discussion Conference IUPAC Polymer Networks, Karlovy Vary, CSSR, September 15–19, 1980     

Local closed world reasoning with description logics under the well-founded semantics

An important question for the upcoming Semantic Web is how to best combine open world ontology languages, such as the OWL-based ones, with closed world rule-based languages. One of the most mature proposals for this combination is known as hybrid MKNF knowledge bases (Motik and Rosati, 2010 [52]), and it is based on an adaptation of the Stable Model Semantics to knowledge bases consisting of ontology axioms and rules. In this paper we propose a well-founded semantics for nondisjunctive hybrid MKNF knowledge bases that promises to provide better efficiency of reasoning, and that is compatible with both the OWL-based semantics and the traditional Well-Founded Semantics for logic programs. Moreover, our proposal allows for the detection of inconsistencies, possibly occurring in tightly integrated ontology axioms and rules, with only little additional effort. We also identify tractable fragments of the resulting language.     

Solid state transformations of Au-Cu-Pt alloys studied by in-situ X-ray synchrotron radiation and DSC

Seven alloys of the ternary Au-Cu-Pt system, containing 75 or 76.5 wt.% Au with 0–15 wt.% Pt and heat-treated to a fully ordered condition, are examined using in-situ synchrotron radiation to determine transformation temperatures and phases formed, and to investigate mechanisms of ordering and disordering. These experiments are complemented by differential scanning calorimetry. Diffraction data show that the alloys can be separated into three groups according to their stable low-temperature ordered phase(s), namely L1₀, L1₂, or the two combined. Platinum increases transformation temperatures in comparison with binary AuCu, two-phase ordered alloys showing the highest transformation temperatures. Details of the evolution of the X-ray diffraction peak structures upon heating and cooling point to significant differences between mechanisms of disordering and ordering: whereas ordering visibly proceeds at significant undercooling by nucleation and growth, disordering appears, from the visible shifts in peak position, to progress in more homogeneous fashion within the alloy.