Operational aspects of adsorption air‐conditioner used in diesel locomotive

A locomotive cabin adsorption air‐conditioner has been equipped in #DF4B‐2369 locomotive; and has been successfully run for 2 years. It is powered by waste heat from the exhaust of the diesel engine. The influence on heat transfer is described by the equivalent heat transfer coefficient or thermal resistance of components inside the adsorber. The variation of adsorption capacity is expressed by a non‐equilibrium adsorption function. The dynamic heat transfer process of adsorption air‐conditioning system is treated with the lumped parameter method. Some typical running experimental results are present. The diesel engine rotating speed and locomotive speed influenced on the refrigeration system are discussed. The maximum mean refrigeration power is regarded as an objective function. Based on experiments and theoretical analysis, the running characteristics of the air‐conditioning system are optimized. Some techniques of performance improvement are suggested as well. Copyright © 2006 John Wiley & Sons, Ltd.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Mining predecessor–successor rules from DAG data

Data mining extracts implicit, previously unknown, and potentially useful information from databases. Many approaches have been proposed to extract information, and one of the most important ones is finding association rules. Although a large amount of research has been devoted to this subject, none of it finds association rules from directed acyclic graph (DAG) data. Without such a mining method, the hidden knowledge, if any, cannot be discovered from the databases storing DAG data such as family genealogy profiles, product structures, XML documents, task precedence relations, and course structures. In this article, we define a new kind of association rule in DAG databases called the predecessor–successor rule, where a node x is a predecessor of another node y if we can find a path in DAG where x appears before y. The predecessor–successor rules enable us to observe how the characteristics of the predecessors influence the successors. An approach containing four stages is proposed to discover the predecessor–successor rules. © 2006 Wiley Periodicals, Inc. Int J Int Syst 21: 621–637, 2006.     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.     

New insights in polarity-dependent oxide breakdown for ultrathin gate oxide

In this work, a quantitative analysis is applied to resolve the newly reported polarity-dependent charge-to-breakdown (Q/sub BD/) data from thick oxides of 6.8 nm down to ultrathin oxides of 1.9 nm. Three independent sets of Q/sub BD/ data, i.e., n/sup +/poly/NFET stressed under inversion and accumulation, and p/sup +/ poly/PFET under accumulation are carefully investigated. The Q/sub BD/ degradation observed for p-type anodes, either poly-Si or Si-substrate, can be nicely understood with the framework of maximum energy released by injected electrons. Thus, this work provides a universal and quantitative account for a variety of experimental observations in the time-to-breakdown (T/sub BD/) and Q/sub BD/ polarity-dependence of oxide breakdown.     

The organisational learning effects of management accounting information under advanced manufacturing technology

This study empirically examined the organisational learning effects of the nonfinancial performance information provided by management accounting information systems (MAISs) under advanced manufacturing technology (AMT). In this study, a target costing system and the frequent and quick reporting of information were considered the facilitators of learning. First, we examined the relationships between AMT level and the amount of nonfinancial performance information produced by MAISs. The empirical results showed that there are significant positive relationships between the level of AMT and nonfinancial performance information. With a systems approach, we also proved the impact of the relationships among AMT levels, nonfinancial performance information and learning facilitators on the organisational performance of a firm. The results of our research suggest that under a high level of AMT, for the provision of information to result in an increase of performance through organisational learning, a target costing system must be introduced and a large amount of information should be provided frequently and quickly. The results of this study also showed that although AMT level may be low, fairly well-arranged facilitators and a moderately large amount of information may be necessary for the improvement of performance. In conclusion, effective organisational learning depends on the provision of relevant information as well as efficient learning support mechanisms.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.