Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

金属及合金中钛的光度分析近况

综述了金属及合金中钛的光度测定方法新近进展情况。     

回火过程应力场计算机模拟

回火过程应力场计算机模拟林家骝，杨振枢，于震宗，段贵明（清华大学）郭剑仁，史全兴，谢克仁（内蒙古第一机器厂）ＡＳｔｕｄｙｏｆＮｕｍｅｒｉｃａｌＳｉｍｕｌａｔｉｏｎｏｆＳｔｒｅｓｓＦｉｅｌｄｄｕｒｉｎｇＴｅｍｐｅｒｉｎｇ￥ＬｉｎＪｉａｌｉｕ；ＹａｎｇＺ...     

填充母料及其他常用塑料母料

塑料母料对推动塑料工业的迅猛发展起了很大作用，其主要特点是：可以简化生产工艺过程：原料混合方便，混炼质量均匀，提高生产效率及制品性能指标；减少粉尘飞扬及对设备的磨损；降低制品在换色时清洗螺杆的用料量；延长原料储存的保质期等。     

两步法合成大粒径丁苯胶乳

研究了聚甲基丙烯酸甲酯（MMA）对丁苯（BS）胶乳的附聚作用以增大丁苯胶乳粒径；探讨了无机盐、体系pH值及体系中MMA胶乳与BS胶乳的固含量比（R值）对附聚后丁苯胶乳的粒径及稳定性的影响。结果表明：适当添加无机盐可以稳定胶乳体系，最佳用量（质量分数）为0．1％～0．2％；适当增大体系pH值，可增大胶乳粒径；在附聚过程中，当R值在两个附聚峰附近时，可增大丁苯胶乳的粒径。     

汽车灯用热熔胶的研究及性能表征

介绍了生产汽车灯用热熔胶的各种原料及其在胶粘剂中所起的主要作用，为汽车灯用热熔胶原料的选择提供了参考。还介绍了汽车灯用热熔胶的制备过程和厂家所需的各种性能及其表征方法。通过选择适当的原料及配比，生产出性能优良并具有良好市场前景的产品。     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.     

异辛酸钴的制备和应用

采用硫酸钴沉淀法制备异辛酸钴,并在水相与有机相的分离过程中添加助剂的方法,可使分离后有机相不经水洗即可彻底除去SO_4~(2-)离子,简化了工艺流程。介绍了异辛酸钴催干剂在4种醇酸磁漆中的应用及其性能检测结果。检测结果表明,异辛酸钴用于醇酸磁漆的性能指标达到或超过规定标准,尤其光泽、硬度两项指标优于同类产品水平,町作为环烷酸钴等常用催干剂的更新换代产品。