Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

吸入短寿命氡子体动物肺组织剂量与体重关系的探讨

本文介绍吸入短寿命氡子体的不同种动物肺组织吸收剂量与体重的关系。实验结果表明,吸收剂量随体重的增加而减小。     

Origin of the threshold voltage instability in SiO/sub 2//HfO/sub 2/ dual layer gate dielectrics

The magnitude of the V/sub T/ instability in conventional MOSFETs and MOS capacitors with SiO/sub 2//HfO/sub 2/ dual-layer gate dielectrics is shown to depend strongly on the details of the measurement sequence used. By applying time-resolved measurements (capacitance-time traces and charge-pumping measurements), it is demonstrated that this behavior is caused by the fast charging and discharging of preexisting defects near the SiO/sub 2//HfO/sub 2/ interface and in the bulk of the HfO/sub 2/ layer. Based on these results, a simple defect model is proposed that can explain the complex behavior of the V/sub T/ instability in terms of structural defects as follows. 1) A defect band in the HfO/sub 2/ layer is located in energy above the Si conduction band edge. 2) The defect band shifts rapidly in energy with respect to the Fermi level in the Si substrate as the gate bias is varied. 3) The rapid energy shifts allows for efficient charging and discharging of the defects near the SiO/sub 2//HfO/sub 2/ interface by tunneling.     

Heading towards an advanced signalling system for multimedia,multiparty services in broadband ISDN

Introduction of the broadband integrated services digital network (B-ISDN) will enable network users to make use of advanced multimedia, multiparty services. With this aim in view, RACE II project R2044, MAGIC, is investigating long-term signalling requirements, architecture and protocols for B-ISDN. New service concepts are being developed in MAGIC which will provide more flexibility when compared to narrowband ISDN (N-ISDN). The service requirements and other signalling requirements, such as the separation between call and associated connections at the network-node interface, are used to determine the distribution of functions over the network. The signalling protocols which are used to exchange the signalling information are subsequently developed. These signalling protocols are simulated to prove the performance and the feasibility of call handling concepts     

单光子时间分辨在线谱仪系统中的接口电路

本文介绍单光子时间分辨在线谱仪系统中的多道分析器与IBM PC/XT微型计算机接口的工作原理及控制程序。     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

Error monitoring issues for common channel signaling

Motivated by field data which showed a large number of link changeovers and incidences of link oscillations between in-service and out-of-service states in common channel signalling (CCS) networks, a number of analyses of the link error monitoring procedures in the SS7 protocol were performed by the authors. This paper summarizes the results obtained thus far and include the following: (a) results of an exact analysis of the performance of the error monitoring procedures under both random and bursty errors; (b) a demonstration that there exists a range of error rates within which the error monitoring procedures of SS7 may induce frequent changeovers and changebacks; (c) an analysis of the performance of the SS7 level-2 transmission protocol to determine the tolerable error rates within which the delay requirements can be met; (d) a demonstration that the tolerable error rate depends strongly on various link and traffic characteristics, thereby implying that a single set of error monitor parameters will not work well in all situations; and (e) some recommendations on a customizable/adaptable scheme of error monitoring with a discussion on their implementability. These issues may be particularly relevant in the presence of anticipated increases in SS7 traffic due to widespread deployment of advanced intelligent network (AIN) and personal communications service (PCS) as well as for developing procedures for high-speed SS7 links currently under consideration by standards bodies     

Ultrasonic thin-walled tube wave structure for sensing devices

Theoretical and experimental investigations of thin-walled tube acoustic wave devices for gravimetric sensing applications are presented. Integrated sensor configurations have been demonstrated by employing a sol-gel processed thin piezoelectric lead zirconate titanate (PZT) film. This was coated coaxially on stainless steel tubes and interdigital transducers (IDT) fabricated as the transmitter and receiver on the curved tube surfaces. We have observed tube waves along both the axial and circumferential directions between 1 and 6.6 MHz. We have also analyzed the mass sensitivities of different modes propagating along the tubes and shown that high mass sensitivity can be achieved by keeping the tube wall thin     

Cast bulk ZrTiAlCuNi amorphous alloys

Cylindrical bulk amorphous samples with diameters up to 10 mm have been prepared by casting ZrTiAlCuNi alloys in a copper mould. In order to rank glass-forming ability as a function of alloy composition, alloys were also cast into wedge-shaped moulds; to a first approximation, the thickness of the amorphous region obtained can be taken as an indication of glass-forming ability. The compositions which lead to the production of bulk glasses all have reduced glass transition temperatures in excess of 0.65 and the extremely high glass-forming ability of these compositions is discussed. We suggest that both the Al and Ti contents are determining factors for the production of bulk amorphous samples and these are believed to reduce the driving force for, and hence the rate of, crystallisation. These amorphous alloys have been found to display high thermal stability and can be annealed for several minutes in the supercooled liquid region. They are ductile at room temperature and have a high value of yield stress.