Performance analysis of multi-antenna relay networks with imperfect channel estimation

In this paper, we present the performance of multi-antenna selective combining decode-and-forward (SC-DF) relay networks over independent but non-identical Nakagami-m fading channels with imperfect channel estimation. The outage probability, moment generating function (MGF) and symbol error probability (SEP) will be derived in closed-form using the SNR statistical characteristics. To make the analysis trackable, we have derived the MGF and SEP for integer values of fading severity, m. Also, to make the relations more simple, we develop high signal to noise ratio (SNR) analysis for the performance metrics of our system. Subsequently, we propose optimal and adaptive power allocation algorithms along with the equal power allocation method. Finally, for comparison with analytical formulas, we perform some Monte-Carlo simulations.     

Comparison of pH-dependent sonodisruption of re-assembled casein micelles by 35 and 130 kHz ultrasounds

Sonodisruption behavior of re-assembled casein micelles was compared at two ultrasound frequencies (35 and 130 kHz) by turbidity measurement and laser-diffraction based particle size analysis. Sonochemical ultrasound (130 kHz) was more effective than power ultrasound (35 kHz) in micelle disruption. This was attributed to the higher strain rates generated upon implosion of cavities, as well as the liberation of more free radicals to the surrounding medium. The higher the pH of solution, the more effective was the ultrasonic disruption due to a looser expanded assembly of particles at higher pH values. Sonochemical ultrasound decreased the consistency coefficient of casein solutions and increased their flow index except at a pH value of 6.35, while power ultrasound did not affect the flow behavior of solutions across the whole pH range.     

Fish oil microencapsulation as influenced by spray dryer operational variables

The effects of spray‐drying air temperature, aspirator rate (drying air mass flow rate), peristaltic pump rate (feed mass flow rate) and spraying air mass flow rate on microencapsulation properties of fish oil including moisture content, particle size, bulk density, encapsulation efficiency and peroxide were investigated. The process was carried out on a mini spray dryer, and skim milk powder was used as the encapsulating wall material. Results indicated that increasing inlet air temperature increased the particle size, encapsulation efficiency and peroxide value but decreased the bulk density and moisture content of product. Increasing aspirator rate resulted in increased particle size and peroxide value but decreased the moisture content and bulk density. Increase in feed mass flow rate increased the moisture content, particle size, bulk density and peroxide value but decreased the encapsulation efficiency of microcapsules. The encapsulation efficiency and bulk density increased with the increasing aspirator rate but moisture content, particle size and peroxide value decreased.     

Determination of phenolic profile and antioxidant activity of pistachio hull using high-performance liquid chromatography–diode array detector–electro-spray ionization–mass spectrometry as affected by ultrasound and microwave

The phytochemicals content and radical scavenging activity of pistachio (Pistacia vera L.) hull extract obtained by different solvents (water, ethanol, and butanol) were measured and compared. Water was selected as superior solvent. Ultrasound-assisted aqueous extraction of the hull by power ultrasound (35 kHz) was more efficient in ascending the phytochemicals content than the sonochemical ultrasonication (130 kHz). High-performance liquid chromatography-mass spectrometry showed increased amounts of vanillic acid, p-coumaric acid, naringenin, and catechin in ultrasound-assisted extracts. Post-extraction sonication declined significantly the phenolics amount and antioxidant property of the aqueous extract. Microwave-assisted extraction increased the phenolics and flavonoids content at extract in a power-dependent trend.     

Effect of heat treatment on foaming properties of ostrich (Struthio camelus) egg white proteins

The effect of heat-treatment on foaming properties of ostrich albumen was investigated. At pH 7.5, coagulation of ovotransferrin (OT) resulted in minimum foaming capacity (FC) and maximum foam density (FD). While both exposure of sulfhydryl groups of ovalbumin (OV) and OT-OV interactions improved FC at lower pH, neither of them had beneficial effect on FC at pH 9. At pH 9, FC and FD were mildly affected by heat-treatment because of less aggregation of OT, then FC decreased due to covalent aggregates composed of ovomucin and OV, but at higher temperatures, higher level of OV unfolding resulted in enhanced FC.     

In situ Measurement of the Adhesion Strength and Effective Elastic Stiffness of Single Soft Micropillar

We report the deformation behavior and mechanical properties of a polymeric micropillar, which measures approximately 10 μm by 30 μm in size by measuring the loading/unloading response using an in situ force measurement system. When the single poly(dimethylsiloxane) (PDMS) micropillar was subjected to compression, we observed a periodic wrinkle and global (Euler) buckling at the sidewall. During unloading, we found the pull-off force (adhesion force) to increase for higher values of preloading and also for lower loading/unloading rates. From the slope of the load–displacement curves measured in situ, we calculated the effective elastic stiffness of the PDMS micropillar to be about 2.03 MPa. In addition to the current work, we report that this method can be used more broadly for in situ measurement of the intrinsic mechanical and adhesion properties of polymers and other relatively soft materials.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Synthesis of nanoporous Baghdadite by a modified sol-gel method and its structural and controlled release properties

In this research, a bimodal nanoporous Baghdadite (NB) (Ca3ZrSi2O9) was prepared by a modified sol-gel method using P123 as a surfactant. The effects of P123's contents on the structural and textural properties as well as the drug delivery behavior of NB were assessed in vitro. The usage of P123 offered a new route for the synthesis of NB. The synthesized NB samples with different amounts of P123 were studied through X-ray diffraction (XRD), Fourier transform infrared spectra (FTIR), N2 adsorption-desorption, field emission scanning electron microscopy (FESEM) equipped with energy-dispersive X-ray analysis spectroscopy (EDAX) and transmission electron microscopy (TEM). The results showed that a single-phase Baghdadite was obtained by this new method at the calcination temperature of 800?°C. It was found that an increase in P123's content up to 0.025?mol changed the morphology of NB samples from mountain-like to needle-like. The potential application of NB samples as drug delivery agents was assessed by estimating their release properties up to 240?h. This research revealed that the synthesized Baghdadite could be used as a potential nanoporous carrier with controlled release capability in bone tissue regeneration.