TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

极尖断面为折线的四极透镜磁性能研究

对传统双曲线极尖的四极透镜进行了磁性能分析。在此基础上，提出了极尖断面为折线的四极透镜结构。磁场的数值分析以及测量结果表明：该结构产生的场梯度均匀，且具有磁场集中、磁场梯度高、便于加工和安装的对称性控制等优点。该结构的四极透镜已用于ＣＹＣＩＡＥ－３０回旋加速器和ＨＩ－１３串列加速器束流输运线之中     

石家庄市室内氡及其子体浓度

本文报道了用双滤膜法对石家庄市室内空气中氡及其子体浓度的调查结果。47个房间室内氡年平均浓度为17.0Bq·m~(-3),氡子体平均浓度是7.14Bq·m~(-3)。氡及其子体浓度的日变化是清晨4—8时出现峰值。季节变化是夏秋季低,冬季高,全年的最低值出现在8月,最高值出现在11月。     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

基于互联网实现多种信息传输技术

随着信息技术的迅速发展,使用互联网实现楼宇内电话、电视、电脑、安防和环境监控、计量数据等信息的合路传输,是实现智能家居和数字楼宇的一种主要发展趋势。最终目的,实现对物和过程的智能化感知。文章首先介绍信息合路编码、中央控管电路,然后介绍网络接口电路原理和系统体系构架。重点介绍多种多样的信息传输技术。它对现代楼宇信息化、智能化建设有很好的参考作用。     

A fonnalism for generating multiparametric encoding gradients in NMR tomography

A general mathematical formalism for generating multiparametric NMR image encoding gradients is introduced. The new schematic approach enables one to construct any desired encoding gradient which may be used in an imaging sequence. Basic gradient waveforms which can be used as building blocks of the desired encoding gradients are presented. A matrix operator for obtaining the encoding gradient for any kind of phase encoding is derived. Specific examples illustrating how to obtain "pure" spatial, velocity, or acceleration encoding gradients for moving spins are presented.