Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

广东省大型工程建设中天然放射性核素引起的环境问题

本文介绍了广东省境内几个大型基本建设工程项目中天然放射性核素引起的环境问题及有关治理对策，并就今后类似建设项目的辐射环境保护工作提出了建议。     

Flame retardant and the degradation mechanism of high impact polystyrene/Fe-montmorillonite nanocomposites

High impact polystyrene/Fe-montmorillonite (HIPS/Fe-MMT) nanocomposites were successfully prepared by melting intercalation. The nanostructures of HIPS/Fe-MMT were testified by X-ray diffraction (XRD) and transmission electron microscope (TEM). Corresponding to pure HIPS, the thermal stability of HIPS/Fe-MMT nanocomposites was notably improved. The peaks of heat release rate (PHRR) and the mass loss rate (MLR) were significantly reduced after the formation of the HIPS/Fe-MMT nanocomposites from cone calorimetry. And nanocomposites PHRR was further lower with the increase of Fe-MMT content in the range of 1 to 5 wt%. The degradation mechanism of HIPS and HIPS/Fe-MMT nanocomposites was conducted by pyrolysis gas chromatography mass spectrometry (Py-GC-MS). And the reason of the enhancement of thermal stability maybe is that structural iron is the operative site for radical trapping in the Fe-MMT and the nanostructure enhances the interaction of the chains of the HIPS.     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

商品混凝土降低成本的技术途径

商品混凝土目前价格偏高 ,用户不情愿接受 ,影响了它的推广应用。针对这一问题 ,本文提出了用“活化填料”、“活化水泥”配制高性能商品混凝土的技术路线并分析了其技术经济效益     

近十年常温干法精脱硫专利技术发展动态

收集了近十年来国内的常温干法精脱硫专利，并分类列举出各种脱硫剂的物化性质和几种常温精脱硫工艺，重点阐述了该技术的优缺点及其未来发展方向。     

Photoelectric conversion of photosynthetic reaction center in multilayered films fabricated by layer-by-layer assembly

Multilayered protein films which contained ordered layers of photosynthetic reaction center (RC) from Rhodobacter Sphaeroides (RS601) were assembled by means of alternate electrostatic adsorption with positively charged poly(diallyldimethylammonium chloride) (PDDA). The assembly of RC was monitored by spectrometry and photocurrent measurement. Linear film growth was observed up to about 20 cycles of adsorption. For the monolayer film, the photocurrent was about 8.5 nA cm⁻². For the multilayered film, the total photocurrent was about 77 nA cm⁻² for the 24-layer RC film, while the average photocurrent increment per adsorption cycle was about 3.2 nA cm⁻². The overall light-to-electricity conversion efficiency for a 24-layer film was about eight times higher than that for the monolayer one. The effects of electrode potential and pH on the photocurrent were also measured to illustrate the light-to-electric converting mechanism.     

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.