Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

The organisational learning effects of management accounting information under advanced manufacturing technology

This study empirically examined the organisational learning effects of the nonfinancial performance information provided by management accounting information systems (MAISs) under advanced manufacturing technology (AMT). In this study, a target costing system and the frequent and quick reporting of information were considered the facilitators of learning. First, we examined the relationships between AMT level and the amount of nonfinancial performance information produced by MAISs. The empirical results showed that there are significant positive relationships between the level of AMT and nonfinancial performance information. With a systems approach, we also proved the impact of the relationships among AMT levels, nonfinancial performance information and learning facilitators on the organisational performance of a firm. The results of our research suggest that under a high level of AMT, for the provision of information to result in an increase of performance through organisational learning, a target costing system must be introduced and a large amount of information should be provided frequently and quickly. The results of this study also showed that although AMT level may be low, fairly well-arranged facilitators and a moderately large amount of information may be necessary for the improvement of performance. In conclusion, effective organisational learning depends on the provision of relevant information as well as efficient learning support mechanisms.