Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Preparation of Protein-Stabilized β-Carotene Nanodispersions by Emulsification–Evaporation Method

This work was initiated to prepare protein-stabilized β-carotene nanodispersions using emulsification–evaporation. A pre-mix of the aqueous phase composed of a protein and hexane containing β-carotene was subjected to high-pressure homogenization using a microfluidizer. Hexane in the resulting emulsion was evaporated under reduced pressures, causing crystallization and precipitation of β-carotene inside the droplets and formation of β-carotene nanoparticles. Sodium caseinate (SC) was the most effective emulsifier among selected proteins in preparing the nanodispersion, with a monomodal β-carotene particle-size distribution and a 17-nm mean particle size. The results were confirmed by transmission-electron microscopy analysis. SC-stabilized nanodispersion also had considerably high ζ-potential (−27 mV at pH 7), suggesting that the nanodispersion was stable against particle aggregation. Increasing the SC concentration decreased the mean particle size and improved the polydispersity of the nanodispersions. Nanodispersions prepared with higher β-carotene concentrations and higher organic-phase ratios resulted in larger β-carotene particles. Although increased microfluidization pressure did not decrease particle size, it did improve the polydispersity of the nanodispersions. Repeating the microfluidization process at 140 MPa caused the nanodispersions to become polydisperse, indicating the loss of emulsifying capacity of SC due to protein denaturation.     

Optimal synthesis of process systems Necessary condition for optimal system and its use in synthesis of systems

The necessary condition for the optimal process system structure which includes both the optimal interconnection and optimal design of processing units is derived in terms of the structural parameters. The structural parameters are essentially splitting factors of process streams connecting processing units. The necessary condition requires the structural parameters and the design vectors to satisfy the weak maximum condition of the Hamiltonian type scalar functions. On the basis of the condition, a search method, evolutionary search for optimal structure (ESOS), for attaining the optimal structure starting from a simple structure is developed and its convergence is proved. An example of synthesizing a reactor-separator system illustrates its use.     

Bone Tissue Engineering in Rat Calvarial Defects Using Induced Bone-like Tissue by rhBMPs from Immature Muscular Tissues In Vitro

This study aimed to induce bone-like tissue from immature muscular tissue (IMT) in vitro using commercially available recombinant human bone morphogenetic protein (rhBMP)-2, rhBMP-4, and rhBMP-7, and then implanting this tissue into a calvarial defect in rats to assess healing. IMTs were extracted from 20-day-old Sprague-Dawley (SD) fetal rats, placed on expanded polytetrafluoroethylene (ePTFE) with 10 ng/μL each of rhBMP-2, BMP-4, and BMP-7, and cultured for two weeks. The specimens were implanted into calvarial defects in 3-week-old SD rats for up to three weeks. Relatively strong radiopacity was observed on micro-CT two weeks after culture, and bone-like tissue, comprising osteoblastic cells and osteoids, was partially observed by H&E staining. Calcium, phosphorus, and oxygen were detected in the extracellular matrix using an electron probe micro analyzer, and X-ray diffraction patterns and Fourier transform infrared spectroscopy spectra of the specimen were found to have typical apatite crystal peaks and spectra, respectively. Furthermore, partial strong radiopacity and ossification were confirmed one week after implantation, and a dominant novel bone was observed after two weeks in the defect site. Thus, rhBMP-2, BMP-4, and BMP-7 differentiated IMT into bone-like tissue in vitro, and this induced bone-like tissue has ossification potential and promotes the healing of calvarial defects. Our results suggest that IMT is an effective tissue source for bone tissue engineering.     

Organic–Inorganic Nanohybrids as Novel Thermoelectric Materials: Hybrids of Polyaniline and Bismuth(III) Telluride Nanoparticles

Thermoelectric materials have received much attention recently from the viewpoint of global environmental issues and effective utilization of energy resources. Especially those effective at relatively low temperature, such as below 100°C, which are usually abandoned without use, have become noteworthy recently. From this point of view, organic thermoelectric materials are most attractive, because they could be prepared at low cost and applied in various locations due to their flexibility. We have investigated the thermoelectric properties of organic conducting polymers such as polyaniline, polypyrrole, and polyphenylenevinylene, and succeeded in increasing the thermoelectric performance by selecting dopants, stretching conducting films, etc. Recently we have focused on new systems of organic–inorganic hybrid thermoelectric materials. Herein we present the preparation of a novel system of hybrids of polyaniline and bismuth(III) telluride nanoparticles, starting from bismuth(III) chloride and tetrachlorotellurium by using polyvinylpyrrolidone as a protecting reagent, as well as their thermoelectric properties. The hybrids prepared by this particular method showed much higher thermoelectric performance than the starting organic conducting polymer.     

Electron holographic 3-D nano-analysis of Au/TiO2 catalyst at interface

Three-dimensional (3-D) nanostructures of gold catalysts supported on TiO2 were analysed by electron holography and high-resolution electron microscopy. The contact angle of the gold particle on TiO2 tended to be >90 degrees in the case of gold particles with a size (height) of >4 nm and it tended to be <90 degrees for gold particles with a height of <2 nm. The change in morphology increases the perimeter at the Au/TiO2 interface as the particle size decreases. This change in 3-D structure should be attributed to a change in electronic structure at the interface. It was found that electron holography enabled 3-D analysis at the atomic level and was effective for analysing nanostructured particles.     

Pinpoint injection of microtools for minimally invasive micromanipulation of microbe by laser trap

This paper reports transportation of the target microbe by the laser trapped microtools with minimum laser irradiation to the target. The size of a microtool (MT) is around micrometer. The MTs are manipulated by the focused laser under the microscope to manipulate the target microbe. Here we propose a pinpoint injection method of MTs at the desired location in the microchamber, which is filled with liquid. At first, we classified the injection method of the MTs in four categories. Here we employed a new method to install the MTs inside the microchamber. We developed a MT holding chip to install the MTs. The MTs were injected in the microchamber, and were manipulated successfully by the laser scanning micromanipulator to transport the target microbe for separation. The proposed method is useful for the pinpoint injection of MTs and separation by the indirect micromanipulation.