Effects of SiC particles codeposition and ultrasound agitation on the electrocrystallisation of nickel-based composite coatings

This study analysed the influence of the codeposition of SiC particles with different sizes: 50 nm, 500 nm and 5 μm, and the type of bath agitation (stirring or ultrasonic) on the electrocrystallisation of nickel coatings. The composites matrix microstructure was analysed by means of SEM, EBSD and XRD, to evaluate the grain size, crystal orientation, and internal stresses and was benchmarked against pure nickel samples electrodeposited in equivalent conditions. The codeposition of nano- and microsize particles with an approximate content of 0.8 and 4 vol.%, respectively, caused only a minor grain refinement and did not vary the dominant?<?100?>?crystal orientation observed in pure Ni. The internal stress was, however, increased by particles codeposition, up to 104 MPa by nanoparticles and 57 MPa by microparticles, compared to the values observed in pure nickel (41 MPa). The higher codeposition rate (11 vol.%) obtained by the addition of submicron-size particles caused a change in the grain growth from columnar to equiaxial, resulting in deposits with a fully random crystal orientation and pronounced grain refinement. The internal stress was also increased by 800% compared to pure nickel. The ultrasound (US) agitation during the deposition caused grain refinement and a selective particle inclusion prompting a decrease in the content of the particles with the larger particles. The deposits produced under US agitation showed an increase in the internal stresses, with double values compared to stirring. The increase in the deposits microhardness, from 280 HV in pure Ni to 560 HV in Ni/SiC submicron-US, was linked to the microstructural changes and particles content.

Graphical abstract

     

A Compact Semi-circular Slot MIMO Antenna with Enhanced Isolation for Sub-6 GHz 5G WLAN Applications

In this paper, a novel compact semi-circular slot (SCS) 2 × 2 MIMO antenna is presented for 5G NR sub-6 GHz applications with high isolation. The proposed antenna consists of a semi-circular slot in ground plane, U-shaped stub, and 50-ohm microstrip feed line. The novelty of this paper are the Semi-Circular Slot acts a radiator, the port isolation  is enhanced using a simple conductor strip as a neutralization line, very compact in size, low ECC, and good impedance matching. The overall size of the proposed SCS MIMO antenna is 16 mm x 21 mm, and FR4 substrate is used with thickness of 1.6 mm. The two SCS antenna elements are separated by edge-to-edge distance of 1mm (\(=0.019\lambda _{0}\)). The proposed compact MIMO antenna design is simulated using Ansys HFSS. To validate SCS MIMO antenna, a prototype was fabricated and tested. The measured results are attained at 5.5 GHz with isolation greater than 25dB, impedance bandwidth (S11\(<-10\) dB) covers from 5.10 GHz to 5.80 GHz with return loss of ? 39.5 dB. The MIMO antenna parameters, ECC, CCL, TARC, and MEG are studied, and the values are obtained within acceptable limits. The measured and simulated antenna results are almost similar. This compact MIMO antenna is suitable for 5G communications in sub-6 GHz wifi-5 band applications.

     

Sicherheit der Rohstoffversorgung unter dem Aspekt der nachhaltigen Entwicklung

The security of future supply with natural resources has to comply with objectives towards a sustainable and responsible development. Resources from the geosphere and recycling material from the technosphere may be grouped in a hierarchy the top of which is made up by fossil energy raw materials and of resources from occurrences which were formed by enrichment processes. The base of the hierarchy is made up by bulk raw materials which occur in unlimited amounts in the crust of the Earth and in the sea water and by waste and residues as potential raw materials. Optimising the efficiency of raw materials takes place if material from a lower level substitutes material from a higher level. Highest efficiency is reached if fossil energy from the top of the hierarchy is substituted or consumption is reduced.     

Groundwater problems in surface coal mining in Scotland

The paper reviews the problems encountered with groundwater in surface mining in Scotland. The problems which occur at various stages of the mining process from initial exploration to mine planning and final restoration are referred to. Special consideration is given to mine drainage and pumping methods.     

Rheological Properties and Characteristics of Hydraulic Transportation and Heat-Mass Exchange of Coal-Water Fuels

The procedure is proposed for calculating the characteristics of flow and heat exchange of coal-water fuels as applied to the pipeline hydraulic transport and heat-mass exchange in the apparatus of ecologically clean combustion in the objects of power engineering.     

Universitärer Forschungscluster „Sustainable Technologies in Metal Production and Processing” (STMP)

Foundation of a university research cluster — Co-operation along the value creation chain from raw materials to components — Evidence of joint performance offers — Utilization of synergies — Integration of Christian Doppler Laboratories — Flexible arrangement of co-operations and networks