Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

The oxidative inducation test applied to medical PVC and other polymers

We have examined the applicability of this simple and effective test to polymer systems widely used in the medical industry. First, it was found that not every polymer examined exhibited a distinct onset of autocatalytic oxidation detectable by DSC. However, for cases where distinct onsets are found, powerful insights can be obtained. These included activation energy of the degradation, thermal oxidative shelf life prediction, and correlation, with product performances. Actual examples are presented to illustrate the utility of the test.     

Modeling the I-V characteristics of fully depleted submicrometerSOI MOSFET's

In this paper, an analytic current-voltage model for submicrometer fully-depleted (FD) silicon-on-insulator (SOI) MOSFET's is presented. This model takes into account the source/drain series resistances which can be especially high in thin film SOI devices. The effect of drain induced conductivity enhancement is also included, which is important for submicrometer channels. The model is verified by comparison to measured SOI I-V characteristics. Good agreement is obtained for SOI film thicknesses ranging from 40 to 220 nm and effective channel lengths down to 0.25 μm     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Epitaxial growth of GaN on (0001) Al<Subscript>2</Subscript>O<Subscript>3</Subscript> via solution-cast seed layer formation process using Ga(mDTC)<Subscript>3</Subscript>

This paper reports an alternative method for the growth of GaN epitaxial layer on (0001) Al₂O₃ substrate by hot-wall vapor phase epitaxy technique. Tris (N,N-dimethyldithiocarbamato)-gallium (III), Ga(mDTC)₃ was introduced as a precursor material for the seed layer formation in the growth of GaN. Optimal growth conditions with seed layers formed by the Ga(mDTC)₃ concentration of 0.047 mol/L were identified: Growth temperature was found to be 850 °C, and optimal distance between the reactant outlet and substrate was determined to be 12.5 cm. Characterization results showed that this growth method produce high-crystallinity GaN epitaxial layers at a relatively lower growth temperature compared to the existing growth techniques and simplify the growth process.     

A process-control and diagnostic tool based on continuous fuzzy Petri nets

The use of Petri nets and fuzzy logic in intelligent process control has caught the attention of many researchers. In this paper, a Continuous Fuzzy Petri Net (CFPN) tool which integrates the three technologies of fuzzy control, Petri nets and real-time expert systems is presented. The CFPN approach can deal with real-time continuous inferencing, for the purpose of process monitoring and diagnostics, at a high level in the presence of uncertainty. This tool has been implemented in the G2 real-time expert-system environment and is currently being used by ESSO Canada.     

Determination of the in situ forces and force distribution within the human anterior cruciate ligament

The in situ forces and their distribution within the human anterior cruciate ligament (ACL) can clarify this ligament's role in the knee and help to resolve controversies regarding surgical treatment of ACL deficiency. We used a universal force-moment sensor (UFS) to determine the magnitude, direction, and point of application of the in situ forces in the ACL in intact human cadaveric knees. Unlike previous studies, this approach does not require surgical intervention, the attachment of mechanical devices to or near the ACL, or a priori assumptions about the direction of in situ force. Anterior tibial loads were applied to intact knees, which were limited to 1 degree of freedom at 30 degrees flexion. The in situ forces developed in the ACL were lower than the applied force for loads under 80 N, but larger for applied loads of more than 80 N. The direction of the force vector corresponded to that of the anteromedial (AM) portion of the ACL insertion on the tibial plateau. The point of force application was located in the posterior section of the anteromedial portion of the tibial insertion site. The anterior and posterior aspects of the anteromedial portion of the ACL supported 25% and 70% of the in situ force, respectively, with the remainder carried by the posterolateral portion. We believe that the data obtained with this new UFS methodology improves our understanding of the role of the ACL in knee function, and that this methodology can be easily extended to study the function of other ligaments.     

Effect of temperature on polymer migration II: Concentration equation

Polymer migration is a generally well-known phenomenon in a flow field, and it has been verified that the sources of such phenomena are nonhomogeneity of the flow, concentration effects and hydrodynamic interactions between the polymer molecules. In addition, temperature effects were found to be another source of polymer migration. The Langevin equation for a polymer molecule was first derived from single chain dynamics using a kinetic theory for the bead-spring elastic harmonic dumbbell model, as described in part I (reference [1]). In this paper the diffusion equation and concentration profile of the polymer molecules induced by a temperature gradient are obtained from the Fokker-Planck equation. A new differential operator is also introduced to calculate the concentration profile. From the concentration equation obtained in the general flow geometry, we find that in dilute polymer solution there are significant effects on the polymer migration not only due to the nonhomogeneity of the flow field but also due to temperature gradients.