Reliability and performance analysis of time – space – time switching networks with multiple separated space switches

Since electronic switching systems usually require very strict reliability requirements as well as good performance objectives, we need to jointly analyse the performance and reliability of switching systems. In this paper, we compare conventional time–space–time switches with single space switches with those with multiple separated space switches, from the viewpoints of reliability and performance. We consider time–space–time switching networks which consist of N incoming time switches, i.e. one NxN space switch, two (N/2)x(N/2) space switches, and four (N/4)x(N/4) space switches. We introduce a Markov reliability model to study the effect of failures and analyse the reliability and performance of three different types of switching networks in terms of average blocking probability and the mean time to unreliable operation, as we vary the offered traffic. As a result, T–S–T switching networks with multiple separated space switches exhibit better performance and reliability than those with single space switches.     

Compact Dipole Antenna for Terrestrial Digital Multimedia Broadcasting Service

A compact dipole antenna for the terrestrial digital multimedia broadcasting (TDMB) application is presented. The length of the antenna is about 0.06λ at the TDMB resonance frequency of 190 MHz. Miniaturization of the antenna is achieved by using meander structures and lumped elements. The proposed antenna has two resonance frequencies and covers the TDMB band from 174 MHz to 216 MHz in Korea. The antenna has good impedance bandwidth and radiation characteristics for the TDMB. The experimental results of the designed dipole antenna are presented and analyzed.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Efficiency increase of an induction motor by improving coolingperformance

Improving the efficiency of induction motors, which are the most energy consuming electric machines in the world, saves much energy. The efficiency can be increased by improving cooling performance as well as by using better materials or by improving electromagnetic performance with better design. This paper presents the relationship between the efficiency or the losses and the temperature of coils with experiments as well as simulations by changing parameters such as the load and the flow rate of cooling air. The losses and the efficiency are calculated from an equivalent circuit method as well as experiments. Coil temperatures variation affects much on the efficiency. The internal cooling method is better than that of external cooling for the coil temperature reduction. Several cooling methods are compared focusing on the fan efficiency and performance, from which the values of the efficiencies of the motors are expected. The fan efficiency as well as the fan performance should be considered for the optimum fan design to increase the total efficiency of a motor. The simulations are validated by the comparison with the experiments     

Influence of nitrate, ascorbic acid, and nitrate reductase microorganisms on N-nitrosamine formation during Korean-style soysauce fermentation.

Traditional Korean soysauce samples were collected from households in Chinju, Gyeongnam, Korea and analysed for volatile N-nitrosamines. Five of 24 samples contained NDMA (range = 1.6-10.4 micrograms/l) which was the only volatile N-nitroso compound found. Soysauce made from well water contained NDMA more often (4 of 6 samples) than soysauce made from tap water (1 of 18). This suggests that the water source is a determinate in the NDMA content of soysauce, probably due to a higher nitrate content of well water. The source of salt used did not clearly influence NDMA content. Soysauce was prepared in the laboratory using traditional methods but with 0 to 400 mg/l nitrate and in some cases made 6.5 to 65 mM in ascorbic acid and fermented for 120 days. The NDMA content of the samples was positively correlated with increasing nitrate concentration. Nitrate at 400 mg/l resulted in an NDMA content of 203 micrograms/l. Ascorbic acid substantially inhibited NDMA formation. All samples contained large numbers of nitrate reductase-containing organisms (greater than 1 x 10(7) CFU/ml).     

Performance of asynchronous DS-CDMA using a maximal ratio combiningdiversity over a Rician fading channel

The final closed-form expression for bit error probability (BEP) is presented for a DS-CDMA system using a maximal ratio combining (MRC) diversity over a Rician fading channel. The accuracy of the BEP estimate evaluated by this expression is verified by comparison with a semi-analytic simulation result. The effect that diversity order has on the BEP is also considered for typical multipath delay profiles with different Rician ratios     

A linear minimum mean square error multiuser receiver inRayleigh-fading channels

We generalize the multiuser (CDMA spread spectrum) communication systems to the fading environments. We first extend Verdu's (1986) conventional optimum receiver to Rayleigh-fading environments and then evaluate its performance. Having no knowledge of the received power at the receiving end, we therefore need an estimator to efficiently estimate the received signal strength of each user in fading environments. A linear minimum mean square error (LMMSE) unbiased estimator is proposed to attain this goal. By using the minimum mean square error (MMSE) Bayesian estimation, we further propose the LMMSE bit estimator for efficient demodulation. Its performance is close to the optimum multiuser receiver but with a much simpler polynomial complexity. To further reduce the complexity, we extend the LMMSE estimator to the sequential LMMSE estimator. In sequential estimation, we do not need to implement the matched filter banks and to perform the matrix inversion when estimating. In addition, it converges after approximately 2k iterations, where k is the number of users. With this fast convergence property and the simple structure, the sequential LMMSE estimator provides an attractive alternative to the implementation of a multiuser system     

Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

A kinetic model for polystyrene (PS) pyrolysis reaction

A mathematical model for the pyrolysis reaction of polystyrene (PS) in a semi-batch reactor has been presented. The thermal degradation of PS was flexibly modeled by a combination of random and specific chain-end scissions. Numerical simulation was used to investigate the effect of operating conditions on the PS products spectrum, the results of which were validated by the experimental data. It was found that as the reaction temperature increased (decreased), the monomer fraction in the products became lower (higher) while the trimer higher (lower). No significant variation in the product composition was, however, observed while constant temperature was maintained. These results indicate the reaction temperature is an effective manipulated variable for the control of products composition of PS pyrolysis. The calculation of the optimum temperature trajectories through the optimization study can thus be of interest for achieving productivity enhancement in plastics pyrolysis processes. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.